Vibration in steel bridge?

12 December 2018 0 9K Report

Sometimes, the designer of vehicle or foot steel bridges ignore some design limitations. this may result in some unwanted vibration in structure although safety is satisfied.what is the possible methods to treat such situations?

Badges
Science topic

More Qasim M. Shakir's questions See All

Cyclic loading in ANSYS ?

How can the Cyclic and repeated loading be represented in the nonlinear finite element program(ANSYS software)?

31 December 2018 7,866 8 View

Calculation of the splitting strength(ft)?

The well-known concrete splitting test can be determined as: ft=2P/(3.14*D*L); I wonder if you have the full derivation of such equation!

11 December 2018 4,349 0 View

Literature about dapped end beams?

I am in need to papers that considered the behavior of the RC dapped end beams with openings to support my experimental study in this area. thanks

11 December 2018 619 3 View

Working in Groups!!!!

Do you think that working in groups to carry out researches may improve the level of article to be published???what are the advantages and disadvantages due to work with a group??

01 January 1970 6,595 6 View

Steel bars of square section !!!

All the steel reinforcing bars using in construction are of circular section, why there is not bars of square sections?

01 January 1970 512 3 View

Your opinion about Islam!!!!!

In your opinion ... Do you think that Islam supports and encourages the development and creativity or it is a religion of backwardness and ignorance ??why??

01 January 1970 743 41 View

Generation of power from car movements!!!

Do you think that generating electricity from traffic road is economically feasible?

01 January 1970 2,279 0 View

Green building philosophy !!!!!

How we can make our houses satisfy green building requirements?schools?universities?Do you think that the green building can be discussed within your specialization?

01 January 1970 6,925 3 View

Structural Engineer as a doctor!!!

In rehabilitation and strengthening structures, there is a philosophy that considers the structural engineer as a doctor and the deteriorated structure as a patient (as infant) that can not...

01 January 1970 10,032 3 View

Construction of steel buildings!!!!!!!!!

Do you think it is time to switch to the steel buildings rather than concrete in Iraq because of the increasing seismic activity ??

01 January 1970 10,205 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

What are the current challenges and future prospects of integrating artificial intelligence into recognition systems for autonomous vehicles?

This question aims to explore the intersection of artificial intelligence and autonomous vehicle technology. It seeks to identify the key challenges faced in implementing AI for recognition...

20 July 2024 3,469 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

Recommendations for Rapid Publication Journals in Traffic and Transportation?

I am currently working on a research paper focused on the control of Connected and Autonomous Vehicles (CAVs) utilizing multi-agent reinforcement learning methods. At this stage, I am seeking a...

14 July 2024 2,620 2 View