Calculation of the splitting strength(ft)?

Qasim M. Shakir @Qasim_Shakir

12 December 2018 0 4K Report

The well-known concrete splitting test can be determined as:

ft=2P/(3.14*D*L); I wonder if you have the full derivation of such equation!

Badges
Science topic

More Qasim M. Shakir's questions See All

Cyclic loading in ANSYS ?

How can the Cyclic and repeated loading be represented in the nonlinear finite element program(ANSYS software)?

31 December 2018 7,593 8 View

Vibration in steel bridge?

Sometimes, the designer of vehicle or foot steel bridges ignore some design limitations. this may result in some unwanted vibration in structure although safety is satisfied.what is the possible...

11 December 2018 8,339 0 View

Literature about dapped end beams?

I am in need to papers that considered the behavior of the RC dapped end beams with openings to support my experimental study in this area. thanks

11 December 2018 447 3 View

Steel bars of square section !!!

All the steel reinforcing bars using in construction are of circular section, why there is not bars of square sections?

01 January 1970 354 3 View

Working in Groups!!!!

Do you think that working in groups to carry out researches may improve the level of article to be published???what are the advantages and disadvantages due to work with a group??

01 January 1970 6,412 6 View

Your opinion about Islam!!!!!

In your opinion ... Do you think that Islam supports and encourages the development and creativity or it is a religion of backwardness and ignorance ??why??

01 January 1970 588 41 View

Construction materials after ten centuries

Do you think that the most used building materials nowadays (steel, concrete and clay) will be considered very old materials after 1000 years?. Nowadays, we consider houses of reeds, stone, logs...

01 January 1970 6,689 4 View

Construction of steel buildings!!!!!!!!!

Do you think it is time to switch to the steel buildings rather than concrete in Iraq because of the increasing seismic activity ??

01 January 1970 10,035 5 View

Structural Engineer as a doctor!!!

In rehabilitation and strengthening structures, there is a philosophy that considers the structural engineer as a doctor and the deteriorated structure as a patient (as infant) that can not...

01 January 1970 9,885 3 View

Presentations in two languages!!!

I would like to publish several presentations discussing different topics in Civil Engineering.Do you think it is beneficial to write the presentation in English only or in Arabic besides the...

01 January 1970 1,432 7 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View