Dear all,
I wan to make UDF for temperature profile in fully developed in internal flow in FLUENT 17.2. But, I do not find sample of this code on the net. do you have the sample UDF for temperature profile of this case?
Thank you for your help
Dear all, I wan to simulate transient heat transfer of conduction heat transfer for ground heat exchanger application by using ANSYS FLUENT. Is fluent capable of doing long term simulation (10...
02 March 2019 7,842 2 View
Dear all, I see in some website just like the following link https://www.computationalfluiddynamics.com.au/tips-tricks-cfd-estimate-first-cell-height/#comment-7768 There are some caclulation of...
31 December 2018 2,917 0 View
Dear All I make ribs in pipe surface by using spaceclaim in ansys 17.2. I make many ribs on the wall. I use small pipe as cutter of big pipe. When I make more ribs, spaceclaim seems has error....
31 December 2018 10,042 0 View
Dear all, I would like to do simulation in spiral pipe but i make extension in inlet part and outlet part by straight pipe. The extension connected with spiral (i attach the file). Critical...
11 December 2018 2,240 0 View
Dear All, I do simulation on helical pipe. I am using Ansys FLUENT 17.2. I want to make plot in cross section of the pipe along axial direction (i show the sample ). How to do it in...
10 November 2018 7,908 0 View
Dear all, I want to make different mesh in the picture because i think its good to reduce computer efforts. Do you have any suggestion? Thank you
09 October 2018 3,746 0 View
Dear all, I want to make simulation in transient heat transfer by using ANSYS FLUENT 17.2. I have one simulation which is success. I wan to re-simulate the same case with temperature change of...
06 July 2018 3,258 2 View
Dear all, I am trying to simulate heat transfer of two phase (stratified) flow to single phase (both flows are turbulent flow). I attach the model of the case. There is no phase change in two...
06 July 2018 1,172 0 View
Dear all, I am new in UDF. I am trying to make different initial guess of temperature distribution in solid by using #DEFINE_INIT CODE in Fluent 17.2. I took the whole code from UDF Fluent...
05 June 2018 4,275 0 View
Dear all, I am trying to simulate conduction in 2D FLUENT 17.2. There are many different type of solid. I get this warning. I have tried to use TUI command...
05 June 2018 6,615 1 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
EMMS - Energy Minimization Multi-Scale
18 June 2024 5,857 2 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?
07 June 2024 9,030 3 View
Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...
05 June 2024 4,153 0 View