Dear All,
I do simulation on helical pipe. I am using Ansys FLUENT 17.2. I want to make plot in cross section of the pipe along axial direction (i show the sample ). How to do it in CFD-Post?
Thank you for your help
Teguh
Dear all, I wan to simulate transient heat transfer of conduction heat transfer for ground heat exchanger application by using ANSYS FLUENT. Is fluent capable of doing long term simulation (10...
02 March 2019 7,842 2 View
Dear all, I see in some website just like the following link https://www.computationalfluiddynamics.com.au/tips-tricks-cfd-estimate-first-cell-height/#comment-7768 There are some caclulation of...
31 December 2018 2,917 0 View
Dear All I make ribs in pipe surface by using spaceclaim in ansys 17.2. I make many ribs on the wall. I use small pipe as cutter of big pipe. When I make more ribs, spaceclaim seems has error....
31 December 2018 10,042 0 View
Dear all, I would like to do simulation in spiral pipe but i make extension in inlet part and outlet part by straight pipe. The extension connected with spiral (i attach the file). Critical...
11 December 2018 2,240 0 View
Dear all, I want to make different mesh in the picture because i think its good to reduce computer efforts. Do you have any suggestion? Thank you
09 October 2018 3,746 0 View
Dear all, I want to make simulation in transient heat transfer by using ANSYS FLUENT 17.2. I have one simulation which is success. I wan to re-simulate the same case with temperature change of...
06 July 2018 3,258 2 View
Dear all, I am trying to simulate heat transfer of two phase (stratified) flow to single phase (both flows are turbulent flow). I attach the model of the case. There is no phase change in two...
06 July 2018 1,172 0 View
Dear all, I am new in UDF. I am trying to make different initial guess of temperature distribution in solid by using #DEFINE_INIT CODE in Fluent 17.2. I took the whole code from UDF Fluent...
05 June 2018 4,275 0 View
Dear all, I am trying to simulate conduction in 2D FLUENT 17.2. There are many different type of solid. I get this warning. I have tried to use TUI command...
05 June 2018 6,615 1 View
Dear All. I am simulating convective heat transfer by using FLUENT 17.2 in 6 meters circular pipe. Inner diameter of pipe is 14.46 mm. Fluid is water and pipe is copper. mass flow rate is 0.033...
04 May 2018 904 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Are both ways acceptable, or is there any convention to them? Thanks.
22 July 2024 6,988 4 View