Asking calculation first cell height in y plus in FLUENT and CFX?

Teguh Hady Ariwibowo @Teguh_Ariwibowo

01 January 2019 0 3K Report

Dear all,

I see in some website just like the following link

https://www.computationalfluiddynamics.com.au/tips-tricks-cfd-estimate-first-cell-height/#comment-7768

There are some caclulation of first cell height of calculator by FLUENT and CFX is different with the same properties.

Do you know the reason of this? Or any reference?

Thank you

Best regards

Badges
Science topic

More Teguh Hady Ariwibowo's questions See All

Asking long term simulation (10 years) for heat conduction in ground?

Dear all, I wan to simulate transient heat transfer of conduction heat transfer for ground heat exchanger application by using ANSYS FLUENT. Is fluent capable of doing long term simulation (10...

02 March 2019 7,715 2 View

Error in Make Ribs in pipe by using space claim ansys fluent 17.2?

Dear All I make ribs in pipe surface by using spaceclaim in ansys 17.2. I make many ribs on the wall. I use small pipe as cutter of big pipe. When I make more ribs, spaceclaim seems has error....

31 December 2018 9,886 0 View

How to chose correct option when laminar and turbulent happens in the same device in ANSYS FLUENT 17.2?

Dear all, I would like to do simulation in spiral pipe but i make extension in inlet part and outlet part by straight pipe. The extension connected with spiral (i attach the file). Critical...

11 December 2018 2,087 0 View

How to plot contour in cross section in helical pipe by using ANSYS FLUENT 17.2?

Dear All, I do simulation on helical pipe. I am using Ansys FLUENT 17.2. I want to make plot in cross section of the pipe along axial direction (i show the sample ). How to do it in...

10 November 2018 7,640 0 View

How to make different kind of mesh in Ansys Meshing in one part?

Dear all, I want to make different mesh in the picture because i think its good to reduce computer efforts. Do you have any suggestion? Thank you

09 October 2018 3,605 0 View

Problem in saving transient simulation in CFD FLUENT 17.2?

Dear all, I want to make simulation in transient heat transfer by using ANSYS FLUENT 17.2. I have one simulation which is success. I wan to re-simulate the same case with temperature change of...

06 July 2018 3,086 2 View

How to simulate convective heat transfer two-phase flow in Horizontal Pipe without phase change?

Dear all, I am trying to simulate heat transfer of two phase (stratified) flow to single phase (both flows are turbulent flow). I attach the model of the case. There is no phase change in two...

06 July 2018 992 0 View

How to solve parse error error in UDF fluent for #DEFINE_INIT?

Dear all, I am new in UDF. I am trying to make different initial guess of temperature distribution in solid by using #DEFINE_INIT CODE in Fluent 17.2. I took the whole code from UDF Fluent...

05 June 2018 3,950 0 View

How to solve many different solid-solid interface solid?

Dear all, I am trying to simulate conduction in 2D FLUENT 17.2. There are many different type of solid. I get this warning. I have tried to use TUI command...

05 June 2018 5,304 1 View

How to simulate convective heat transfer by using periodic boundary condition in small temperature gradient?

Dear All. I am simulating convective heat transfer by using FLUENT 17.2 in 6 meters circular pipe. Inner diameter of pipe is 14.46 mm. Fluid is water and pipe is copper. mass flow rate is 0.033...

04 May 2018 781 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Any suggestions for a website that allows you to create questionnaires and gather unlimited data (Totally free)?

I have found only four of them; www.surveyplanet.com www.online-anket.gen.tr www.surveey.com and of course google forms. Expecting to see your suggestions if there is any. Thank you

28 February 2021 3,237 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View