Dear all,
I want to make different mesh in the picture because i think its good to reduce computer efforts.
Do you have any suggestion?
Thank you
Dear all, I wan to simulate transient heat transfer of conduction heat transfer for ground heat exchanger application by using ANSYS FLUENT. Is fluent capable of doing long term simulation (10...
02 March 2019 7,842 2 View
Dear all, I see in some website just like the following link https://www.computationalfluiddynamics.com.au/tips-tricks-cfd-estimate-first-cell-height/#comment-7768 There are some caclulation of...
31 December 2018 2,917 0 View
Dear All I make ribs in pipe surface by using spaceclaim in ansys 17.2. I make many ribs on the wall. I use small pipe as cutter of big pipe. When I make more ribs, spaceclaim seems has error....
31 December 2018 10,042 0 View
Dear all, I would like to do simulation in spiral pipe but i make extension in inlet part and outlet part by straight pipe. The extension connected with spiral (i attach the file). Critical...
11 December 2018 2,240 0 View
Dear All, I do simulation on helical pipe. I am using Ansys FLUENT 17.2. I want to make plot in cross section of the pipe along axial direction (i show the sample ). How to do it in...
10 November 2018 7,908 0 View
Dear all, I want to make simulation in transient heat transfer by using ANSYS FLUENT 17.2. I have one simulation which is success. I wan to re-simulate the same case with temperature change of...
06 July 2018 3,258 2 View
Dear all, I am trying to simulate heat transfer of two phase (stratified) flow to single phase (both flows are turbulent flow). I attach the model of the case. There is no phase change in two...
06 July 2018 1,172 0 View
Dear all, I am new in UDF. I am trying to make different initial guess of temperature distribution in solid by using #DEFINE_INIT CODE in Fluent 17.2. I took the whole code from UDF Fluent...
05 June 2018 4,275 0 View
Dear all, I am trying to simulate conduction in 2D FLUENT 17.2. There are many different type of solid. I get this warning. I have tried to use TUI command...
05 June 2018 6,615 1 View
Dear All. I am simulating convective heat transfer by using FLUENT 17.2 in 6 meters circular pipe. Inner diameter of pipe is 14.46 mm. Fluid is water and pipe is copper. mass flow rate is 0.033...
04 May 2018 904 0 View
I want to know more about diamond ore deposits in world.
08 August 2024 1,514 0 View
A website software of Blackbody radiation law expert software can used through the following web site. http://39.105.188.151:3000/index
07 August 2024 1,706 0 View
to identify themes in question with APA style references
07 August 2024 2,239 5 View
I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...
05 August 2024 9,805 3 View
I want to know more about petroleum deposits in Iran.
02 August 2024 8,725 3 View
I am conducting a qualitative study that uses interviews to investigate the perceptions of teachers about a particular leadership practice and I am focusing on 3 schools which have a total number...
01 August 2024 8,457 10 View
I am excited to announce an opportunity for dedicated researchers to join our dynamic team for an ongoing meta-analysis study. If you are passionate about research and have a keen interest in...
01 August 2024 6,737 1 View
I want to know more about laterites in Iran.
31 July 2024 8,219 2 View
Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...
30 July 2024 5,206 1 View
Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...
28 July 2024 6,553 1 View