22 October 2016 1 1K Report

1) phenotype expected to see and why (mechanisms involved)

2) What other strategy might produce a similar result and how would it work?

More Rahul Raman's questions See All
How to interpret multiple bell shaped curves in Kratky plot?

Hi, I'm trying to analyze a Kratky plot generated from my SAXS data. I am seeing multiple bell-shaped curves in my Kratky plot and I am not able to find any source to get relevant info on this...

20 January 2021 2,474 1 View

Lift off problem with Indium/Gold deposition?

Hi, I'm doing 5/40nm In/Au e-beam evaporation at rates 0.2A/s(for In),1A/s(Au) on lithographically(doubly coated 495k,950k PMMA e-beam resist) done Si substrate at base pressure 2e-6torr. I'm...

18 January 2021 7,550 4 View

How to Import .inp file from abaqus CAE to Ansys perfectly?

I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.

17 January 2021 5,450 3 View

Can I know the reason for these non specific bands?

a PCR and gel electrophoresis was carried out to obtain the results. they are negative jak2 v617f samples (ref genome - NG_009904 )

13 January 2021 7,658 4 View

Which third party CFD Codes can be used for FSI Co-Simulation in Abaqus ?

Since Abaqus CFD is no longer available in newer versions what are other available codes for Fluid-Structure Interaction Simulation

11 January 2021 2,012 3 View

How to determine Viscoelastic and Hyper Elastic Material Properties for Abaqus by mechanical testing ?

I am studying about Impact load resistance property of Polyurea (Elastomer). With respect to this, I need to conduct tests on this material to evaluate its material model behavior as a...

29 December 2020 2,969 1 View

How to remove rotation along z-axis and shift the origin to body's center?

I have attached the files with this post to explain me how to remove rotation and center the origin at the body's local coordinate. This is just one sample and I have 1000s of files like this. I...

18 December 2020 3,838 3 View

Reason for growth of fungus/mould in hydrothermal liquifaction filtered product of cellulose-based materials?

Performed hydrothermal liquefaction of cellulose powder, at about 200 degrees for 10 16 hours. After simple filtration, I stored filtered product at room temperature for 4-6 days, there is the...

03 December 2020 7,327 3 View

Is Coefficient of Variability (CV) positively correlated with root mean squared error (RMSE) in every case??

My data for fungicide treated replication shows higher RMSE and R-square but less CV compared to the untreated replication for a regression between vegetation indices and yield. How correct is it?...

23 November 2020 2,079 6 View

Fuel Cell not working after charging?

I am making an electric fuel-cell car using platinum as an electrode and sodium hydroxide as an electrolyte. I tried both series and parallel connection to charging it, Even after charging 2...

17 November 2020 2,860 9 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What solvent can I used for Paal Knorr reaction between 6-amino hexanoic acid and 2.5 hexanedione?

I am try to make the Paal Knorr reaction between 2.5 hexnedione and 6-amino hexanoic acid, my problem is type of solvent to use, because 6-hexaminohexanoic acid is soluble in water but I am not...

02 March 2021 4,443 2 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close