Reverse engineering a protein - kind of?

I want to bind a peptide to a hydrogel and test the release kinetics over time using an ELISA. BUT, there is no antibody/ELISA available for my peptide. So, I know that the molecular weight of my...

29 October 2018 3,907 3 View

Does anyone know where I can get the list of genes which are known downstream targets for the transcription factor CEBPB?

Using Enricher I can see that my gene set contains 235/3478 genes known to be targets of CEBPB via the Transfac/Jasper tab. Does anyone know where i could get the list of all the CEBPB genes so...

10 February 2016 1,814 3 View

Does anyone know of research looking at the effects of repeated viral infection in first few weeks of life in a mouse to model childhood illnesses?

17 November 2015 9,908 3 View

Is it beneficial to use ELISA to quantify p53 levels in cultured cell fractions?

ELISA and western blots are only as good as the antibodies used to make them - but despite a plethora of published westerns for measuring p53 there are very few reports using ELISA. I have...

21 November 2012 8,474 14 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View