Statistical analysis using RSM is an older practice which has been already well reported and well documented?

More Munish Gupta's questions See All

How can we co-relate the cutting force with the cutting energy?

I want to know the basic relation of cutting force with the cutting energy.

10 November 2016 10,037 4 View

Regarding some turning experiments?

I have to performed turning experiments on some materials by using some parameters. But the work is specific to the chosen materials and cutting insert. Therefore, the selected parameters and the...

09 October 2016 9,022 8 View

How root mean square (Rq) and maximum peak to valley (Rz) values contributing surface measurement apart from average surface roughness (Ra) ?

Can anyone suggest it?

09 October 2016 7,347 3 View

What is the effect of cutting speed and feed rate on high stresses at tool edge?

Can anyone tell me the relationship between cutting speed and feed rate with stresses

07 August 2016 2,391 4 View

How can we calculate surface roughness during turning?

Based on cutting speed, feed rate, depth of cut and cutting zone temperature.

11 December 2014 6,388 6 View

What is the effect of recrystallization temperature on microstructre and micro hardness?

Cooling analysis effect on metallurgical behavior?

11 December 2014 5,686 9 View

What is the best parameter design or matrix used to perform a minimum number of experiments, if I have 3 parameters and their 3 levels?

All possible combinations should be used.

11 December 2014 1,718 2 View

How can I reduce a chattering in CNC lathe machine during turning of operation?

How we can select the diameter and length of workpiece during turning operation to reduce chattering effects?

10 November 2014 1,929 5 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Daniel Martinez Krahmer

RSM is an statistical tool like others. You can use this tool without problems, because is only a tool. The important is your experimental work.

Munish Gupta

Thank you sir

Rajiv Pandey

Dear Mukesh

RSM is excellent technique for optimisation. You have to judge which method should be applicable for your experiment.

Thanks

Ok thank you sir,