Why does my error file shows this warning message continuously but the solution is still going on?
The error picture is attached
Try these solutions if you have a connection in your model
1- Change the detection method (e.g from Gauss points to nodes).
2- Reduce the contact stiffness by changing Normal Stiffness
Hello, I want to use all the 9 constants of concrete for solid 65 . Where can get all the values for these parameters as the first four are always used so I have the idea about that but how the...
31 December 2017 5,729 3 View
I'm performing the analysis of shear wall with foundation 76*27*16 inches and the wall of dimension 48*144*4 inches in apdl. When the displacement controlled lateral cyclic loading is applied on...
31 December 2017 1,230 1 View
Hello, I am solving a RC wall model and I have observed that if I do the analysis for some time, then with only the linear properties, it is solved faster but as soon as I give a nonlinear...
31 December 2017 8,266 2 View
In my model during analysis, there is seen a local failure near the area where the load is applied so I tried using a load plate but it still doesnot work. 1. What can be done to rectify this ? 2....
11 December 2017 2,137 0 View
I am working on a verification of RC shear wall subjected to cyclic loading using ANSYS APDL 14.50 but the results given by ansys are far different from that of the experimental results. - I used...
11 December 2017 3,630 2 View
I m performing analysis of shear wall which is constrained at the bottom and I have obtained the results. But in order to plot the reaction solution of the nodes at every time step, It has become...
11 December 2017 7,062 1 View
I am applying a displacement controlled loading on a shear wall, I am using drucker prager parameters in the material properties, I want to capture the bauschinger effect. How can I do that in...
10 November 2017 9,581 2 View
Can anyone suggest some papers where I would find values of cohesion, dialatancy angle of concrete to be used for drucker prager model in ansys?
08 September 2017 3,483 0 View
For a cantilever beam with point force at end, I have analysed by apdl and got different reaction forces at different nodes (at the fixed point). how to get the single value of reaction force?
07 August 2017 9,310 6 View
I am currently solving a rc beam in Ansys. I have done everything perfectly and checked it many times but it always shows the error that solution not converged at a particular time and some load...
05 June 2017 7,051 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...
06 August 2024 4,953 0 View
Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...
04 August 2024 6,033 0 View
Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...
30 July 2024 2,744 1 View
When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!
29 July 2024 488 0 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...
28 July 2024 6,553 1 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
I am preparing to run a lot of samples on a 384 well plate and I wanted to test if any well in my PCR machine is dead so as not to lose any data. I would really appreciate help with how I can do...
24 July 2024 8,172 1 View