Hello,
I want to use all the 9 constants of concrete for solid 65 . Where can get all the values for these parameters as the first four are always used so I have the idea about that but how the other parameters are decided?
Thanks,
Refer to ANSYS element library and you will find all you need about solid65
Please see:
http://www.ansys.stuba.sk/html/elem_55/chapter4/ES4-65.htm
Thanks to all for information
Why does my error file shows this warning message continuously but the solution is still going on? The error picture is attached
31 December 2017 4,298 1 View
I'm performing the analysis of shear wall with foundation 76*27*16 inches and the wall of dimension 48*144*4 inches in apdl. When the displacement controlled lateral cyclic loading is applied on...
31 December 2017 1,230 1 View
Hello, I am solving a RC wall model and I have observed that if I do the analysis for some time, then with only the linear properties, it is solved faster but as soon as I give a nonlinear...
31 December 2017 8,266 2 View
In my model during analysis, there is seen a local failure near the area where the load is applied so I tried using a load plate but it still doesnot work. 1. What can be done to rectify this ? 2....
11 December 2017 2,137 0 View
I am working on a verification of RC shear wall subjected to cyclic loading using ANSYS APDL 14.50 but the results given by ansys are far different from that of the experimental results. - I used...
11 December 2017 3,630 2 View
I m performing analysis of shear wall which is constrained at the bottom and I have obtained the results. But in order to plot the reaction solution of the nodes at every time step, It has become...
11 December 2017 7,062 1 View
I am applying a displacement controlled loading on a shear wall, I am using drucker prager parameters in the material properties, I want to capture the bauschinger effect. How can I do that in...
10 November 2017 9,581 2 View
Can anyone suggest some papers where I would find values of cohesion, dialatancy angle of concrete to be used for drucker prager model in ansys?
08 September 2017 3,483 0 View
For a cantilever beam with point force at end, I have analysed by apdl and got different reaction forces at different nodes (at the fixed point). how to get the single value of reaction force?
07 August 2017 9,310 6 View
I am currently solving a rc beam in Ansys. I have done everything perfectly and checked it many times but it always shows the error that solution not converged at a particular time and some load...
05 June 2017 7,051 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...
06 July 2024 2,130 0 View
What heavy aggregates are available for protective concrete in your country?
01 July 2024 1,625 3 View
What are the benefits and advantages of concrete flooring when used in parking lot floors, and what are the technical requirements and general specifications that should be considered to ensure...
29 June 2024 2,171 5 View
Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...
29 June 2024 6,192 2 View
I submitted my journal and got some comments, I have answered and corrected all the comments from the reviewer but I don't understand how to answer this question. any expert researcher help me to...
20 June 2024 3,802 1 View
What are the realistic applications of self-compacting geopolymer concrete in the world? Are there names of projects implemented with this concrete around the world? Please mention the names and...
20 June 2024 6,040 2 View
If you can share it with me, please email it to [email protected]. Many thanks in advance! Mohammad
19 June 2024 2,143 7 View