Solution not converged, run continued at user's request in ansys apdl?

Why does my error file shows this warning message continuously but the solution is still going on? The error picture is attached

31 December 2017 4,188 1 View

What are the Constants of concrete of solid 65 element?

Hello, I want to use all the 9 constants of concrete for solid 65 . Where can get all the values for these parameters as the first four are always used so I have the idea about that but how the...

31 December 2017 5,593 3 View

How to rectify the error of too much element distortion in apdl?

I'm performing the analysis of shear wall with foundation 76*27*16 inches and the wall of dimension 48*144*4 inches in apdl. When the displacement controlled lateral cyclic loading is applied on...

31 December 2017 1,148 1 View

What can be done if there is local failure in model in apdl?

In my model during analysis, there is seen a local failure near the area where the load is applied so I tried using a load plate but it still doesnot work. 1. What can be done to rectify this ? 2....

11 December 2017 2,038 0 View

While modeling of RC shear wall that subjected to cyclic loading in ANSYS , analytical results differs from experimental results ?

I am working on a verification of RC shear wall subjected to cyclic loading using ANSYS APDL 14.50 but the results given by ansys are far different from that of the experimental results. - I used...

11 December 2017 3,551 2 View

How can I get reaction solution for by constrained nodes at every time step in ANSYS apdl?

I m performing analysis of shear wall which is constrained at the bottom and I have obtained the results. But in order to plot the reaction solution of the nodes at every time step, It has become...

11 December 2017 6,950 1 View

How do use bauschinger effect in ansys apdl?

I am applying a displacement controlled loading on a shear wall, I am using drucker prager parameters in the material properties, I want to capture the bauschinger effect. How can I do that in...

10 November 2017 9,458 2 View

Where will I find the values for the parameters of Drucker Prager model?

Can anyone suggest some papers where I would find values of cohesion, dialatancy angle of concrete to be used for drucker prager model in ansys?

08 September 2017 3,358 0 View

How to integrate the reaction forces on all nodes in ansys apdl?

For a cantilever beam with point force at end, I have analysed by apdl and got different reaction forces at different nodes (at the fixed point). how to get the single value of reaction force?

07 August 2017 9,095 6 View

What is convergence depended upon in ansys apdl?

05 June 2017 6,971 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View