Should i use a connector for a piston in abaqus?

More Eirini Pitsiougka's questions See All

Is it possible to have higher TMRE fluoresence intensity signal in H2O2 treated cells rather than cells treated with H2O2+antioxidants?

I treated SK-N-SH cells with 1mM H2O2 and 1mM H2O2+antioxidants (3 different mixtures) and measured the mitochondrial membrane potential (ΔΨm) with 500nM TMRE. As far as I know, H2O2 and ROS...

18 October 2021 2,706 14 View

How to graph non expression in some of the treatments in RT-qPCR?

Hello everyone. I have an experiment of 5 treatments (including the control) and have checked several genes of interest. Some of these genes were expressed in some treatments but not others. When...

28 December 2020 8,576 4 View

Which is the correct way to analyze RT-qPCR data in paired and unpaired samples?

I have read the relevant paper from Schmittgen and Livak (2008) to explore the examples. I have also extensively read and combined all the threads on Research Gate involving answers about RT-qPCR....

30 November 2020 6,488 9 View

How do i calculate equivalent von Mises stress in a 2d fem model?

I want to calculate the equivalent stress for an elasto-plastic analysis.Which is the correct way to do it: 1) Calculate stresses at each Gauss Point and then evaluate equivalent stress at each...

30 September 2020 2,519 3 View

Stable gene silencing without viral vctors??

I am looking to create stable cell lines HCT116 for gene silencing . I am not satisfied with the siRNA experiments ( not great transfection efficiency so far and

28 February 2020 4,202 3 View

Regeneration of phosphorus in microalgae batch bultures?

Is it possible to notice an increase in phosphorus concentration in batch cultures of microalgae strains after several days of normal decrease of nutrients?

11 June 2019 5,146 3 View

How much is the proper salinity in ppm for egg water in zebrafish?

After the breeding, I used egg water for the eggs and the majority are dying. So, I am trying to check the parameters. Any other ideas of what might have gone wrong?

05 March 2019 4,803 2 View

Hi there, I'm currently searching for a 2D or a 3D coastal cliff erosion model. Any suggestions?

There's quite a few models on coastal beach or dune evolution, however neither of them include coastal cliff erosion modules.

05 February 2019 856 4 View

Can higher order Lagrange shape functions increase the continuity inside the element?

My question is can we have higher order continuity inside an element while it has C0 continuity between other elements?For example a plane element has C0 continuity between elements can we...

30 January 2019 1,676 3 View

Does C-1 continuity of the stress field leads to not accurate approximation of it?

In linear fem for truss and plane elements we have C-1 continuity regarding stresses.Does that lead to a worse accuracy or approximation than C1 continuity?

23 January 2019 2,432 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

Identity behind this address?

May I request for change of pofile for this email address? It belongs to the ofice of the head of institution but the name attached is different. Kindly also include [email protected] being the...

17 July 2024 1,145 0 View

Mohamed Yassin Baraya

If your study is concentrated on the piston head only, I suggest to use BC's because applying the interaction properties will be a challenge.

Qasim M. Shakir

following the answers

Eirini Pitsiougka

Mohamed Yassin Baraya No my study is concentrated on the piston,pin and connecting rod.Its static analysis