"Mesh Leak "error in ansys Maxwell simulation ?

17 April 2019 1 6K Report

I am working on do my simulation in Ansys Maxwell, but I find a problem

"Mesh leak is found for certain objects. Please validate the model, do the geometric repair on certain objects. (8:46:31 AM Apr 17, 2019)"

the question is I can not find any issue for my model, can anybody know where should I repair for my model? how can I find the error on my model?

Thank you!

Steven

Saad Najeeb

Mr. Steven Cong...

Can you change the type of element and then choose the element number.

Good luck.

Badges
Science topic

More Steven Cong's questions See All

Why am I not able to use all VEP programs for the in silico analysis of avpr1b SNP's?

Good day researchers I am busy analysing the predicted effects of certain SNP's in AVPR1b. When using the VEP prediction programs (SIFT, Polyphen, FATHMM, LRT, Provean, Mutation Assessor, and...

28 February 2021 5,197 1 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

What metal thin film houses also do annealing?

Could anyone provide names of metal thin film deposition vendors that also do high temperature annealing, in the range of 300-500 C?

27 December 2020 6,137 3 View

Vacuum freeze drying protocol in human skeletal muscle tissue methods, anyone?

I will be freeze-drying small skeletal muscle samples (~60mg) per sample using a Virtis SP Scientific Benchtop Pro Freeze Dryer. I've had difficulty findings a reference protocol to determine the...

21 November 2020 1,423 1 View

Suggestion for normal ovary cell lines?

Dear all, I want to choose a normal ovary cell line and check for its proliferation property when introducing carcinogenic factors. Does anyone have any suggestions for the cell line? Many thanks...

08 November 2020 9,100 3 View

Does anyone freeze samples in GeneJET RNA extraction kit lysis buffer?

For the GeneJET RNA purification kit from Thermo Scientific, does anyone know if you can lyse your sample (suspension cells in my case) in the lysis buffer from the kit and then keep the sample at...

18 October 2020 4,993 3 View

Looking for good/reliable betaine assay kits. Does anyone have experience with such a thing?

I am looking to quantify both human serum and skeletal muscle homogenate betaine concentrations via ELISA or colorimetric assay kits. Has anyone had a good experience with any products...

24 September 2020 4,550 3 View

Accurate curvature estimation of CT-scans (image stack)?

We have multiple CT-scans in the format of TIF image stacks. To get the mean curvature we first transform the stack to a triangular mesh (using Marching Cubes). To make the triangles in this mesh...

03 August 2020 7,921 4 View

Which experiments could clearly show the immune-enhanced diseases in SARS-CoV-2 vaccine study ?

Now there are many studies of SARS-CoV-2 vaccines in animals and human. One of the concerns relating to safety of vaccine is the immune-enhanced disease. But I wonder which animal experiments...

14 May 2020 5,179 10 View

What can I do to submit my revised manuscript when I cannot log in the Editoral Manager system of a Journal?

When I first submitted my manuscript, the journal was using the EVISE system. After getting the "Request revision" status, I have revised it. However, the journal has changed from EVISE system to...

29 March 2020 7,570 9 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View