Primer for coated paper board

More Z.M. Khodabakhsh's questions See All

How to measure phonon energy or cut-off phonon frequency of any solid (like oxides) ?

"Phonon energy" is typically used to describe the resonance energy of lattice vibrations. As the host phonon energy decreases , we need more number of phonons to bridge the energy gap between...

15 February 2018 1,293 4 View

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

Anybody with an idea on how do design specific primers for detecting tomato resistance genes tm-1, TM-2 and Tm2^2?

I am trying to identify these 3 genes among some tomato cultivar collections and after aligning some sequences from NCBI, I couldn't find unique sequences to target for specific primers. There...

28 February 2021 606 3 View

What is the ideal efficiency for a qPCR?

hello everyone, I need to do standard curves for my qPCR, what is the ideal efficiency range? I tried a primer (Mglu2 receptor) that gave an efficiency of 90.2%. Is it accepted?

28 February 2021 1,254 3 View

Segun Michael Abegunde

I believe this will help

Z.M. Khodabakhsh

Thanks Segun for your help, but I am looking for a water based primer that dry with IR dryer. The method of printing for primer is Flexo and then an inkjet method print the ink, Finally a layer of varnish print on the ink by flexo method. Please let me know if you know more about water based primer that dry with IR.

Many thanks,

Guat Yee Toh

Probably you can try out with water based polyurethane as primer too..