Is there a way to convert grayscale KITTI dataset images to color or visa versa?

I'm working with the KITTI stereo dataset having 4 cameras. Two of them are grayscale and the other two are color. I need all four of them to be the same. Directly converting the color ones to...

18 October 2020 8,937 1 View

How to quantify different phases of clay minerals (percent) of marine sediments using XRD?

Hi, I am interested in quantifying the abundances of different phases of clay minerals of marine sediments using XRD analysis. Any suggestions regarding the detailed method/software will be...

03 September 2020 3,031 8 View

Is it possible to publish article without any references?

All articles we have seen in different journals published with references. What will happen, if anyone submits an article considering his/her own thought without referring any citation/references?...

18 May 2020 9,381 14 View

What is the best way to compare a 2d image with a 3d mesh/point cloud?

I want my mesh to be as similar to the input image from the given angles as possible. So im taking projection of the mesh and comparing it with my input image. Currently im taking the outline of...

25 April 2020 954 2 View

How to find the 1-D correlation between two images?

I came across a paper where they mentioned 1-D correlation between two images without any explanation for it. The height and width of the output was same as the input image. Paper:...

06 April 2019 3,150 6 View

What can be the ideal rheological characteristics of a polymeric solution used for oral drug delivery?

Hello Everyone, I have made the polymeric solution of two different polymers. My aim involves preparation of beads from this polymeric solution and encapsulation of my drug to these beads that I...

26 August 2018 6,958 11 View

What value of acoustic impedance should be set for In2O3 and Er2O3 in e-beam evaporation?

We know different material has different density and acoustic impedance. A particular value needs to be specified to get the actual deposition thickness of a particular material through thickness...

18 August 2018 1,269 7 View

How do I determine the best Order to run my butterworth filter, using SAC?

how to decide order of butterworth filter that best suit to filtering in Seismic Analysis Code (SAC).

26 June 2018 3,563 2 View

What is LD50 dose of gamma irradiation for balsam

18 May 2017 1,642 3 View

Looking for a good software (free) to analyze XRD data of natural rock samples. Need your suggestion. ?

I am a geologist and interest to identify different minerals present within the natural rock samples like quartz, feldspar etc, also interestd about different clay minerals like keolinite, illite...

09 November 2016 8,387 7 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View