What is the best way to quantify the specific antibodies against the venom in my neutralization assay?

07 August 2014 3,353 8 View

Is IgY non-specific and if so how do I overcome the non-specific binding?

I am trying to develop an ELISA that is coated with an antigen and specifically binds IgY. What I am seeing is that a control IgY is non-specifically binding as well. Is IgY non-specific? If so...

03 April 2014 1,598 3 View

Extraction of glycerol from restriction enzymes

What is the best method for extraction of glycerol? Dialysis seems to be lowering the activity of the enzymes.

07 August 2012 6,651 2 View

I have immunoglobulins from canine plasma, but they are contaminated with albumin. What is the best single step to remove albumin?

I do not have access to chromatography. I have read that zinc or copper will precipitate the albumin.

09 October 2011 8,053 6 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View

How to seperate PEG-4000 from aqueuse phase ?

Hello everyone , Please tell me if It possible to seperat POlyethelyn glycol -4000 from an aqueuse media by other ways rather heating . I have tried salting out by electrolyte solution to...

22 February 2021 7,285 5 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View