LS-DYNA. MAT_PLASTIC_KINEMATIC, Definition of FS factor?

14 July 2016 1 9K Report

When using MAT_PLASTIC_KINEMATIC, there is a FS factor which is defined as: FS:=Failure strain for eroding elements. Where can I find this strain for various steels?

I have an example where for S235 it is 0.78, what is the physical meaning of this value?

Thanks,

Nirmala S.V.S.G

Dear Andrej Boiko

please check pdf

Badges
Science topic

More Andrej Boiko's questions See All

Can we prove that set of all nested continued fractions N^N and the set of positive real numbers R^+ are homeomorphic?

Let us have a general sequence a in N^N Question 1 If we simply insert that sequence into the nested fractions, then we get a0+1/(a1+1/(a2+1/(a3+...))) It seems that for any such sequence we...

11 September 2023 8,065 5 View

Bone imunohistochemistry sectioning for analysis?

Hello everybody! I need to section a bone for immunohistochemistry. We have classical paraffin and cryo histology. For any advice or protocol, I will be very thankful. Thank you.

09 January 2023 9,474 1 View

Any help with PCR that is not working at all?

Hi, I have a problem with not working PCR. I am trying to amply two fragments next to each other on chromosome with Q5 high fidelity polymerase. I had problem with amplification of both. I tried...

01 November 2021 3,980 9 View

Langmuir adsorption isotherm, linear or non-linear fit?

Hi, when constructing a Langmuir (or any other) adsorption isotherm form experimental data, is it better to use a linear form of the equation [1/qe=1/(Kl*qm*ce)+1/qm] with linear fit or use...

21 April 2021 3,579 11 View

What do you think about issue with research on sociolinguistic competence?

Hi everyone. I'm actually doing a study on the teaching of sociolinguistic competence. I'd like to know what you think of research on the area of sociolinguistic competence. I noticed that more...

01 October 2020 9,576 3 View

Which Human Reference Transcriptome for RNAseq?

I am currently conducting a RNAseq experiment of different human blood cell populations. I decided to go with Salmon for quantification of the samples as it seems to be one of the best algorithms...

18 February 2020 8,437 3 View

How to compare marker expression of cells with different autofluoresence?

I my experiment I want to assess changes in monocytic cells by flow cytometry after a specific treatment. For example after treatment I want to compare CD14 expression of treated cells vs. control...

19 December 2018 763 10 View

What mobile phase should I use (TLC) to separate aromatic hydrazone and aromatic hydrazine?

Hydrazone (Nitrogen nitrogen double bond), hydrazine (single bond)

11 June 2018 6,256 2 View

Are there anybody experienced in analyzing the RTG/CT (x-ray, axial computed tomography) from elasmobranch species ?

We are conducting pioneer X-ray and compute tomography studies on chosen species of elasmobranches. Research so far included rough shark, Oxynotus centrina (L.) (Squaliformes: Oxynotidae),...

02 December 2016 5,810 7 View

Cell-Based Bioassay | Any tips on increasing assay window?

Hi all, I wonder if there are any tips reg. increasing the assay window? We perform 4-fold dilutions for 10 points. Currently in our case, if the initial concentration is relatively high, the...

19 January 2016 2,511 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View