28 February 2022 1 5K Report

In older basin modeling software such as Genex, it was possible to view sedimentation rates with burial history. Is this possible in the new version of basin modeling software?

More Arsalan Zeinalzadeh's questions See All
Can you help in Linkage Analysis Tool?

Can anyone assist with running the Linkage Analysis Tool 'Easylinkage' or any alternative tool for conducting linkage analysis and calculating LOD scores?

06 April 2024 7,273 2 View

Hi there, does FBS has anything to do with MSC detachment in culture?

I had two cell types: MCF-7 and AD-MSCs that were cultured in DMEM low glucose. MCF-7 cells first were cultured in DMEM high glucose and then adapted to low glucose. but suddenly my cells started...

17 February 2024 5,593 0 View

Kegg Network Disease Analysis Pathways?

Literature suggests that potential candidate genes in mastitis, but I couldn't locate few of them in the mastitis pathways within the KEGG database. Should I explore another genes for research, or...

13 September 2023 1,114 0 View

How to solve issue of sink and source in Ansys Q3D?

HI Researchers, I am facing an issue while simulation my Ciruict which is imported from (PCB designer to Ansys Q3D simulation) After assigning all the sources and sinks on the object/face the...

06 September 2023 1,484 0 View

How I can characterize some noble metal bonded in hydroxide form to some support?

With due respect, I want to inquire about that how I can characterize some noble metal bonded in hydroxide form to some support. We can usually see with the XPS as there would be some binding...

18 September 2022 8,126 5 View

Whats the Difference between sonication or stirring effect in order to remove porogen?

Hi, I am preparing porous Carbon using some porogen.....After calcination, I need to remove the porogen by using HCL( 2M usually) but the thing is what procedure should I use either sonication or...

16 April 2022 6,042 6 View

I ask about new model for IWQI Irrigation water quality index?

Hi Dears I ask about IWQI Any one now about New model for assessment of irrigation water quality index or changing model (Brown etal 1972) water quality index to IWQI. kind regards ARSALAN

14 February 2022 4,957 2 View

Why Bule colour of methylene blue has come again when remove the samples from sunlight.?

During the study of photocatalytic properties of Zno/Cuo i kept the samples of methylene blue with certain amount of photocatalyst in sunlight for degradation. After some time the colour of...

21 January 2022 6,311 6 View

What is the best tool in order to simulate the reinforced soil with numerical study methods?

I have some experimental results of soil reinforced in large scale with static and static-cyclic loading and i want to verify my result in a numerical study and examine some other parameters and...

19 October 2021 2,024 1 View

How can we investigate the reinforced soil by analytical study based on experimental results?

For example we have some experimental results and then we want to use an analytical method to predict the settlement by using the variable parameters of the experimental model.

27 August 2021 4,170 4 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close