Is it possible to design HER-2 aptamer based amperometric electrochemical sensor ?

02 June 2018 1 1K Report

HER-2 is the most important biomarker for breast cancer screening, and to design electrochemical sensor , the transducer used is based on the bio-marker bio-receptor interaction, is it possible to design amperometric based HER2 aptamer ?

Shawana Tabassum

Hi Tasneem,

Yes it is possible. Please look at this. This articles talks about HER2 aptamer based breast cancer detection

Article Aptamer selection and applications for breast cancer diagnos...

Badges
Science method

More Tasneem Harahsheh's questions See All

I'm conducting a study on Research Commercialization in Pakistani HEIs and would appreciate your participation in a brief survey?

Dear Participants- Faculty and Researchers from Pakistani Higher Education Institutions, Thank you for participating in research study that aims to 'Analyze Individual and Institutional Factors...

18 July 2024 7,024 1 View

Inter item correlation less than .30?

Can I find references that support Inter item correlation less than .30 when piloting on a small sample of 21 where population is less than 100. Scale having 180 items.

07 June 2024 8,228 0 View

Minimum sample size for a mix method pilot study?

What is the minimum sample size for a pilot study in a mix method research?

28 May 2024 1,044 8 View

Webserver for identifying activation and repression of TFs, genes, and miRNAs?

Hello. Is there any webserver where I can input a set of transcription factors, genes, and miRNAs, and it can provide me with statistical data on how TFs either activate or repress genes and...

18 May 2024 5,848 1 View

How to perform protein-ligand simulation on CYP51 protein with a heme group using gromacs?

Hello, I want to perform 100ns GROMACS simulation using CHARM27 force field on a protein-ligand complex where my protein is CYP51 (PDB ID: 5V5Z) which contains a heme group covalantly bonded to...

26 December 2023 9,309 2 View

How to solve the error in gromacs "Warning: Only triclinic boxes with the first vector parallel to the x-axis are supported" ?

Hello, I am getting the error below almost at the end of the simulation performed using gromacs 2023.1 . I am sure I did not encounter this problem before with the same input files. This has just...

08 October 2023 5,428 0 View

How to pronounce 2' when talking about chemical structures or data? for example in NMR structure numbering?

04 October 2023 9,340 2 View

How to solve the error "unbalanced atom charge" in OSIRIS property explorer??

Hello, I need to analyze the pharmacokinetic properties of my compound using the OSIRIS property explorer. The compound's SMILES ID is: C[N+](C...

12 August 2023 5,283 0 View

How to solve the "Possible problem with molecular topology file in ligand" error in SwissParam?

Hi. I am trying to create ligand topology and parameter files using SwissParam webserver. I followed all the steps to create the .mol2 file available in SwissParam page:...

02 August 2023 7,324 5 View

What can be a potential reason for crack in the sample after dry etching SiO2 using CHF3?

I did SiO2 dry etching using CHF3 (100 W RIE power, 10 mT pressure, 20 sccm CHF3 flow) at 20C. After the etch process, I noticed cracks/peeling off in multiple places of my sample (image...

18 July 2023 7,663 3 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Radiogenomics Cancer Research Challenges?

what are the top 3 challenges to the advancement of the field of Radiogenomics in cancer research? is it the availability of easily available low-cost matched imaging and biosamples with clinical...

03 August 2024 5,828 4 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

Seeking Software Recommendations for SELEX NGS Data Analysis?

I am looking for software to help analyze SELEX NGS data, including alignment, sequence enrichment, and other related tasks. Can anyone recommend suitable tools or software? Best wishes, Waleed

30 July 2024 1,061 5 View

How to prediction 2D to 3D aptamer?

Hello, I have a little problem. Well, right now I only have the DNA aptamer sequence. I went to see the 2D model form with DNA folding. After that, I used RNA Composer to simulate in 3D and used...

30 July 2024 6,794 0 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

MAGeCK Plotting Error: Logarithmic Axis Must Have Positive Limits?

I have been running a MAGeCK test command on the terminal for a CRISPR screen to rank sgRNAs and genes based on the read count tables. However, I get only the plot of the top-ranked genes...

28 July 2024 9,811 1 View