In Perform 3D, out of inelastic bar and concrete strut which is a better option for masonary strut modelling?

More Niharika Talyan's questions See All

How can I make the CST simulation run faster?

I am trying to simulate a metasurface of 24x24 elements, but even with a GPU of 48GB it takes very long to simulate. I want to obtain the field along the defined curve.

10 June 2024 3,577 7 View

Why is my protein concentration increasing after storage at -20°C?

I have a few proteins that I produce recombinantly in E. coli cells. All of them are disordered proteins and are stored in the presence of 4mM DTT at -20°C before use. One of them also contains...

28 November 2023 2,682 2 View

Why do A431 cells form clumps in propidium iodide staining solution?

I've been trying to study cell cycle using PI (propidium iodide + Triton-X + sodium citrate)b staining solution. I trypsinize my cells (A431: skin carcinoma), fix them using 100% methanol and...

20 November 2023 2,443 3 View

Not getting any protein expression. How to tackle the issue?

I am trying to express a novel GlcNAcT enzyme in BL21(DE3). I have successfully cloned it in pET28a vector and confirmed it through sequencing. I tried following previous protocols for GlcNAcT...

19 July 2023 6,064 2 View

Is there any public database that has both chest x-rays and CT Chest available?

The NIH has separate databases for chest x-rays and CT Chest but I am looking for any public one that has both available to compare some variables between both.

12 July 2023 3,530 2 View

How to obtain sensitivity from cst?

I am working on obtaining sensitivity of microstrip patch in cst but I cannot seem to understand how to obtain the plots in the paper ( page 6044/fig 8). I manually derived the formula for...

27 February 2023 5,663 0 View

How to conduct qualitative detection of sialic acid using resorcinol method on TLC plates made with silica gel??

I am qualitatively trying to determine the sialic acid using resorcinol on TLC plates. Can someone help me with the process?

26 January 2023 7,825 0 View

How do I grow WI-38 (human normal lung) cell line?

I have WI-38 cells. Although the cells look healthy, they are growing very slow,. I have increased the serum (FBS) from 10 to 15%, cultured in high glucose and high glutamate media, yet it is not...

05 December 2022 6,450 2 View

What is the role of 8M urea in protein purification buffer besides solubilization?

Hello, I am trying to express and purify recombinant nuclear pore proteins in E. coli cells. All the published protocols I have found use 8M urea in the lysis buffer and subsequently during...

19 October 2022 4,623 5 View

How to get sample wise allele frequency in a VCF file?

Given a multi sample VCF file how to obtain AF for each sample in the file

17 October 2022 2,525 1 View

How do we reduce the tensile force on the side of the wall without prestressing?

There is the torque on the wall, which tends to rotate it. As it rotates, the diagonal forces down, the ground resists and compression is created. The other side of the wall, raises forces which...

23 March 2024 8,422 3 View

Link element approach ?

I am performing Non linear dynamic analysis.While performing these analysis on SAP2000 , I have to model a strut modeling approach for showing the properties of masonar wall. I have to use LInk...

20 March 2024 402 1 View

How can I calculate a low WSS area percentage on a stented artery wall?

Supposing we are analyzing blood flow through a stented artery. I have been simulating one strut of a stent on the artery wall as a 2D axisymmetric model (I attached an image of the geometry). If...

04 February 2024 5,905 0 View

Are there any optimized strut and pore size for bioprinted skin?

I am doing research on 3D-printed skin substitutes, however, I don't see any related articles reporting this. Any suggestions for reading? Thanks

07 January 2024 4,146 0 View

How to find the function of diameter of largest sphere that can be inscribed in the voids of lattice structure made of IsoTruss unit cells?

An IsoTruss unit cell is shown in the picture. The unit cell is strut based and cuboid. There are cylindrical struts or rods. The function of diameter of largest sphere is required in terms of...

17 October 2023 4,773 2 View

How to image an array of cells (artificial tissue) with a 3D scaffold?

Dear community, we have the following problem. We populate porous 3D-printed scaffolds made of PLA (cube shape, 8x8x8 mm) with cells and want to monitor their distribution and growth in the pores...

21 September 2023 694 0 View

What is the most properly way to model a flexible diaphragm in OpenSees?

I am modeling masonry walls using a strut and tie methodology for this kind of structures. I want to know how can flexible diaphragm be implemented in this platform.

03 May 2023 8,457 1 View

Why Abaqus cannot merge a part in assembly module?

My entire model is made up of several number of struts. All Struts have the same area and shape. In assembly module, after I finished my entire geometry, I want to merge all of them as a geometry....

29 December 2022 867 2 View

Is there a way to incorporate the effects of printing parameters (in 3D printing) to finite element (FE) models?

I know, for example, that you can use a Gaussian distribution in order to model the heterogeneities introduced in the strut diameter of lattice structures. Then, using Timoshenko beams, FE models...

17 August 2022 4,960 0 View

Abaqus: truss element distortion?

Hello! We are modeling a timber bridge in Abaqus. The trusses of the bridge are supported by struts at the sides. We are experimenting with different types of connections and element types to...

01 March 2022 5,509 2 View

Prabhakar Gundlapalli

Good to see your problem statement. But, response of in-fill was studied by hundreds of researchers, earlier. Include some novelty and missing links from previous works.

Niharika Talyan

Prabhakar Gundlapalli i have a software related query.

I have referred literature on this subject and have adopted single strut for my study. As per the literature i have done infill modelling previously in other softwares without any issue. But in Perform 3D i got 3 options to model single strut. So wanted to know what other users of Perform 3D software are opting for and why.