I would like to do research on modeling and experimental study for new type of renewable fuel. Does any one have similar experience on modeling of combustion in IC engines and sensitive parameters to be optimized?
If it were at Chennai, India, I would say YES
Try Prof. Wachtmeister at TU Munich
Thank you Prof Dr. Lenkamp.
I am looking for PhD supervisor in a German university on research topic IC engine modeling. You can send me contacts via email: [email protected]
You can also try with Prof. Peter Tzscheutschler (his email address is [email protected]), he works at Technical University of Munich.
I was there for some weeks, and they have an amazing test facility for testing of cogeneration devices, based on IC and Stirling engines.
In India, ARAI tests so many automotive engines with various alternative fuels. Please contact the ARAI, Pune employees to get details.
http://waset.org/publications/14450/theoretical-modeling-and-experimental-study-of-combustion-and-performance-characteristics-of-biodiesel-in-turbocharged-low-heat-rejection-d.i-diesel-engine
Which components of the IC engine are affected?
05 June 2014 249 3 View
It's known that low ethanol blended gasoline fuel up to E10 results in an economic save as well as a reduction in emissions with out any modification on the engine system while on the other...
01 February 2014 3,324 14 View
Cleaning a heat pipe is important to control the concentration of the nanofluids during performance testing. Nano-particles are reported to form a layer on the inner surfaces of the device's wick...
07 August 2013 5,400 1 View
In case of top cooled horizontal porous wicked condenser plane surfaces, liquid may move by capillary action into a two dimensional plane along the porous body rather than dropping down in the...
07 August 2013 194 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...
09 August 2024 9,621 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View