I want to model RC column with CFRP and epoxy in abaqus. Can someone guide me?

Do I need to define an epoxy layer with separate material properties between column and CFRP or should I define material properties with epoxy.Or any better way? Kindly share material properties...

08 February 2021 4,204 3 View

Either SEM analysis are enough to justify the morphology and micro structure of activated carbons? or I should go for TEM analysis as well?

While I was discussing my nitrogen adsorption isotherms in the context of micropore, mesopores, total pore volume for activated carbon samples prepared from waste materials, I received a review...

13 November 2020 1,971 3 View

How to get clearer TEM analysis of carbon (hollow) nano-crystal / quantum dots ?

I am working on hollow carbon quantum dots. During the TEM analysis, it is very difficult to get a clearer image of the crystal structure due to the extremely small size. I want to measure the...

15 October 2020 3,610 3 View

Rebuttal to editors decision ?

Does anyone has ever got acceptance after rebuttal to the editor's decision? In my case, one reviewer accepted and one reviewer rejected the manuscript, but the reason of rejection is minor and is...

20 May 2020 3,581 19 View

Can somebody help me to understand the DTG curves of activated carbon samples obtained from TGA analysis?

I have carried out the TGA analysis of my activated carbon samples after study the literature but I am not able to explain the DTG curves the peaks and depths of these curves can somebody help me.

10 March 2020 8,817 4 View

Either pore size matters for conducting BET tests or not?

I want to conduct BET analysis for getting Carbon dioxide and Nitrogen adsorption curves for activated carbon samples, I am confused either pore size matters for BET analysis or it can be done for...

05 March 2020 5,077 3 View

Activated carbon colour matters or not?

i have prepared the activated carbon from pomegranate peels under the mentioned condition when i heat the furnacr upto the 700 degree celecious as from literature the sample turned its colour to...

20 November 2019 5,852 2 View

How can integrate contour layer in CNN using caffe?

Dear All, Is there anyone who is using contour in CNN for segmentation in 3D Caffe library, please? Regards, Mumtaz

05 June 2018 9,890 1 View

Metal-ligand aqueous complexes molecular weight determination method?

09 August 2016 6,925 4 View

What are the possible products of the reaction between cobalt(II)acetate tetrahydrate and hydrogen peroxide?

30 March 2015 1,818 20 View

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

Anybody with an idea on how do design specific primers for detecting tomato resistance genes tm-1, TM-2 and Tm2^2?

I am trying to identify these 3 genes among some tomato cultivar collections and after aligning some sequences from NCBI, I couldn't find unique sequences to target for specific primers. There...

28 February 2021 606 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

What is the ideal efficiency for a qPCR?

hello everyone, I need to do standard curves for my qPCR, what is the ideal efficiency range? I tried a primer (Mglu2 receptor) that gave an efficiency of 90.2%. Is it accepted?

28 February 2021 1,254 3 View