I have degummed the silkworm cocoons with 0.03M sodium bicarbonate and dried it overnight at room temperature, and added 9.3M LiBr on the top of dried fibers in the 20:80 ratio but my solution becomes gel instead of dissolving.
Linu Mithran Karthikeyan
You need to dilute the gel with water. Then the treated cocoons will dissolve.
I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...
08 August 2024 4,812 2 View
We are doing simulations of fdsoi ncfet in synopsis tcad can someone correctly explain how to match the ferroelectric capacitance and mos capacitance
06 March 2024 7,511 0 View
I am simulating a tension test of a bimaterial specimen in ABAQUS. I would like to create different field outputs for each material, and I would like to display them in a single contour plot. For...
20 January 2024 4,613 4 View
I would like to know if it is a common reagent kit for the target amplification of both DNA and RNA, or does it show amplification only for the RNA targets. Will the presence of DNA in the sample...
18 December 2023 7,062 2 View
Currently, I am working on algae-based wastewater treatment. in order to check the effect of various parameters towards treatment efficiency, I want to vary the COD, Nitrate, Nitrite, and...
13 September 2023 3,584 3 View
How it enhance acedemic or industrial career? thanks in advance
29 August 2023 2,899 3 View
Recently I submitted the SCAPS simulated manuscript to one of the RSC journals and I have taken some of the parameters from the literature as all the SCAPS papers have done the same. can anyone...
15 August 2023 2,560 0 View
Aflatoxin concentration Zon toxin concentration Ochratoxin concentration
25 July 2023 1,636 4 View
in a typical MFC H+ ions will form in anode chamber. it is supposed to go through the membrane to the cathode. many of the research papers use CEM. how is it possible, since H+ and NH4+ are the...
14 June 2023 2,798 1 View
Currently, I am working in microbial fuel cells I want to collect secondary data and analyse it to make a predictive model. while collecting I can't find all the data in verbal form. they were in...
14 May 2023 1,000 2 View
I got these smeared bands quite often lately. We typically run the gel at 140V with a 10-12% gel and do a wet transfer at 220 mA for 1.5 hr in cold room. We also noticed some dirty spots/dots (see...
10 August 2024 7,480 3 View
I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...
06 August 2024 3,130 2 View
I am having an issue with my gel image where my PCR product is not appearing very bright on the gel. When I perform gel extraction, the A260/280 purity value is very low. I used the Qiagen gel...
05 August 2024 9,798 3 View
Hello everyone, I performed a PCR yesterday, and the results showed no bands on the gel. Of course, I probably missed some crucial steps, like adding my samples to the PCR strips themselves, for...
31 July 2024 2,406 6 View
We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...
30 July 2024 942 2 View
I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...
29 July 2024 950 4 View
I am performing IgG purification and I have to show my results on SDS-PAGE. I use 10% tris glycine gel and prepare the samples under non reducing conditions. I am new to antibodies and therefore...
23 July 2024 6,664 6 View
Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...
23 July 2024 4,019 3 View
Hello everyone, A collaborator sent us his protocol in order to be able to use his immunohistochemistry kits. But one step contains PBS + 0.3% H2O2 + 0.1% sodium azide. Knowing the dangerousness...
23 July 2024 6,314 3 View
Hello, I was running a 12% SDS Page electrophoresis on few granulosa cell samples and got this result after the ponceau staining. The total protein lysate seem to aggregate at 70 kDa ladder mark...
21 July 2024 5,128 4 View