I am trying to coat my material on steel coating but the final coating is producing cracks ?

2 weeks ago 1 7K Report

I am using zn as active material using 90 mg with 20mg Polyvinyl butyral resin and droping the mixture using pippete on to steel surface after sonicating for 2 hours but the final coating gets cracked

Stefan Krakowiak

Your coating is probably over-pigmented. Try reducing the amount of zinc dust.

stefan

Badges
Science topic

More Paul Thomas's questions See All

How can women be responsive when they can make love for hours?

… with my present female lover … she and I spend anywhere from two hours to six hours in caressing, touching, cuddling, hugging, lip kissing, deep kissing and intimate conversation before,...

11 August 2024 4,521 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Why do men not accept that continually hassling for sex proves that they want it more than their partner?

Your partner’s not there to service you, it’s not their job to keep you sexually satisfied. You’re together because you love each other and want to make each other happy. Constantly hassling them...

08 August 2024 1,491 0 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

Why do women not understand that men are aroused by physical contact?

Women often complain that their husbands never touch them unless they want sex. (Michele Weiner-Davis)

02 August 2024 7,778 2 View

Why do women usually need more persuading than men do to have sex with a new lover?

Women need to feel a degree of sexual intimacy before sex becomes desirable… For women, intimacy sometimes results in sex; for men, sex sometimes results in intimacy. (Marina Muratore)

31 July 2024 8,860 0 View

Why do men and women confuse platonic love and sex?

Women associate affection with love. … Men associate affection much more directly with sex. … Men see affection of any kind as a sexual invitation. Many women find this bewildering. (Kramer &...

30 July 2024 9,498 2 View

Does anyone have experience electroporating SKOV3 cells with a large plasmid using Neon transfection?

I have been trying to electroporate SKOV3 cells with a large plasmid (11kb) without much success. Any tips?

29 July 2024 3,229 1 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

A positively charged and 10x his-tagged protein that doesn't bind to any chromatographic resin?

Hello everyone, I am currently working on a protein that is 10x his-tagged and positively charged (predicted pI=10.16). But when I tried to use Ni-NTA column to purify the protein, it's not...

24 July 2024 7,293 4 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Prevent sedimentation and maintain the suspension of powder particles in the resin ?

Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...

23 July 2024 1,672 0 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Any relation between resin viscosity（mPa*s）and resin relative molecule weight？why the former is used in manufacture?

https://en.wikipedia.org/wiki/Viscosity

21 July 2024 3,089 4 View