I am new in PETREL. And I am wondering if it is possible to exceed the number of problems to more then 100 while I run the simulation?

More Onkar Prakash Bhujange's questions See All

Hello, my question is that; what happens when we shine different light beam of different wavelength on the same nanoparticle at the same time?

It is known that plasmon resonance effect is seen when a light of wavelength greater than the size of the nanoparticle is shined upon. However, what would happen when different light of...

08 August 2023 4,780 2 View

What kind of thinner I can use for a viscous photosensitive acrylic monomer used in stereolithography?

I use a DWS System's DS3000, a photosensitive monomer to disperse the nanoparticles in it and use the solution for SLA printing. But, because of its high viscosity, I cannot increase the particle...

03 July 2023 1,598 2 View

What are the optimum conditions for electrical polarization of BTO, PEGDA 250 composites at room temperature?

20 March 2023 6,373 0 View

What is the JCPDS card number of Ti3C2Tx MXene sheets?

09 March 2023 6,776 2 View

Does the Auger sensitivity depend on the electron beam energy?

What is Auger sensitivity? What is electron beam energy in AES?

04 January 2023 8,392 3 View

How can I change the dimensions and properties such as nozzle diameter, strength of NICD, AICD in petrel. Also, how to add AICV in Petrel?

when I design the completion in Petrel. It takes the dimensions of AICV and ICD automatically. Is it possible that I provide the dimensions for these flow control devices? Also, I cannot find the...

23 April 2022 2,566 0 View

How to do reverse engineering method by HPLC-RID,ELSD etc for estimation of Glycerol Mono-stearate (GMS)?

I want to estimate Glycerol Mono-stearate (GMS) from a Cream formulation as a part of Reverse Engineering. I have HPLC-RID and ELSD. Could some one help me to guide on this?

11 November 2019 832 1 View

What tests can be performed to check penetration of sugar syrup in(to) GulabJamun, an Indian Sweet, and related properties of sugar syrup therein?

Gulab Jamun is an Indian traditional sweet item, in which balls made of mixture of Khoa (concentrated/condensed milk solids) and wheat flour (maida) are soaked in sugar syrup of specific...

23 April 2018 9,231 3 View

In DSC curve, how to calculate Cp of solid phase and Cp of liquid phase...?

For study of melting behaviour and thermal properties of Paraffin wax, DSC is carried out. The tests are carried out in dynamic mode with heating rate of 10 K/min, where melting occurred at 57 oC...

23 April 2018 7,892 3 View

what is the material of the boom used in the satellite(in the link) ?

https://youtu.be/ORc6DqYUytg What is the material composition? Is it plastic or composite?

26 January 2018 7,944 1 View

Can someone explain me how to insert the actual distance between two well logs in Petrel (picture attached)?

I uploaded two well logs to the "Well section window" of Petrel and they were attached together without any space. Then, I modified the horizontal scale from "relative" to "constant (50)". They...

12 June 2024 8,666 2 View

How do i change the Start time in seismic geometry in Hampson and hampson russell Geoview?

i want to change the seismic start time in Hampson and Russell, i import the data from petrel. In petrel the zero point is not same as the seismic that i load in Hampson and Russell. Is there any...

11 April 2024 8,034 2 View

How can I upload data in petrel and eclipse software and run it?

I am learning to use the Eclipse and Petrel software from schlumberger.

30 March 2024 8,306 3 View

How to perform seismic inversion using Petrel software?

09 February 2024 7,783 0 View

If I only have data from 1 well, can variogram analysis be carried out for the distribution of facies and property?

How do you do variogram analysis if you only have 1 well data?

01 February 2024 2,912 3 View

In petrel, do you know why a well is correctly displayed in 2D window (checkshots are corrects) and not in a 3D windows ?

I have some issues with wells in Petrel: A well is at the right position in 2D interpretation window whereas it's not in a 3D window (see screenshots). I do not understand why. Any idea ? In 3D it...

08 December 2023 9,125 1 View

How to determine base value, minimum and maximum in the variable tab for uncertainty analysis?

Hi, I'm working on uncertainty analysis using petrel. In the variables tab, there are base value, minimum and maximum. How to determine base value, minimum and maximum?

23 November 2023 8,259 3 View

Error in CMG Builder when importing PVT model?

Hello everyone, and thank you in advance for reading/answering my question. I have built my gelogical model in PETREL software exported it into Rescue format and imported it into CMG Builder, to...

19 November 2023 3,672 1 View

What is sptr issue in 2d seismic data due to cropping? how to rectify it when loading to petrel?

I have some 2d seismic data which is cropped from both ends and when I suppose to load in petrel their navigation has been disturbed. Some lines are dislocated, some are inverted, like actually...

18 November 2023 6,257 0 View

My interpreted faults in petrel is showing broken lines instead of solid line, hence making it difficult to edit. what could be the cause?

Please what could be be reason why all interpreted solid fault lines suddenly changed to broken lines with difficulty to even edit after activating the fault?

03 October 2023 7,924 1 View

Pierre Bergey

I suggest you provide a bit more details relative to the question. What do you call problem? Are you in DELFI or on premise, ....

Onkar Prakash Bhujange

I have added the SS. My simulation stops every time as problem count reaches 100. Is it possible that I can exceed it to more than 100?

Methaq Aljafar

To address the question, I believe it requires some clarity.

Warm regards.