How can we get average velocity of of open channel by integrating over the channel height and length?

I am following one paper about the "Electrokinetic actuation of low conductivity dielectric" but did not understand the equation 35 derivations. Can anyone please help me to find Maxwell gradient...

01 February 2020 9,439 3 View

Is it possible to get 1700 v from 25 mm^2 area from tribo nanogenerator?

I am following this paper but the results are too high to get from mentioned data? Can anyone guide me about this? Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelec...

04 May 2019 2,716 1 View

How can I measure or check the adhesion( interface force) between cured consecutive layers of PDMS?

Let suppose we make a PDMS lines( 50um) on glass/PET substrate and after fully curing PDMS, we cover the PDMS lines by spin coating with PDMS and again cured the whole sample. Now, how can I...

02 March 2019 3,033 4 View

Why DMA(Dynamic mechanical analysis) results of shape memory polymers are showing odd behavior?

04 May 2017 6,024 4 View

Whats can be expected applications of 2 different shape memory polymers layered one another?

Dear all, If we have 2 different shape memory polymers with different glass transition temperatures, layered one another along the thickness, then what can be expected applications? What can be...

03 April 2017 9,922 1 View

How wave length dimension play a role in curing time for 3D printing?

I am trying to cure my photo polymer using SL 3D printing technique, but material is not being cured by UV light of 405 nm. What type of parameters should be changed to cure my material?

31 December 2016 5,130 1 View

Can we fabricate four different polymers using 3D technique?

11 December 2016 8,479 0 View

Can we use our own polymer resin for SLA and Multi Jet 3D printers?

I have my own resins, how can I confirm that they are compatible for SLA and Multijet 3D printers?

10 November 2016 4,685 2 View

Which type of methods can be used to fabricate a functionally graded polymer?

Let suppose, we have two type of materials, one is in liquid shape and other one is in powder shape, is it possible to make FGM type structure?? IS possible then how can we proceed?

09 October 2016 4,353 1 View

What is difference between graphite and CNT in terms of mechanical properties?

Dear researchers, How can we differentiate CNT and graphite without characterization techniques like SEM, XRD??

09 October 2016 8,427 2 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

What is the best solvent to remove PDMS from nano particles?

I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...

24 February 2021 7,845 5 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View