I am following this paper but the results are too high to get from mentioned data? Can anyone guide me about this?
Article Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelec...
i am also confuse how they calculateed the power density and current density by using which formula
I am following one paper about the "Electrokinetic actuation of low conductivity dielectric" but did not understand the equation 35 derivations. Can anyone please help me to find Maxwell gradient...
01 February 2020 9,562 3 View
I have followed all the parameters and also changed them as well. But still values are 10000 times lower than the published one. I have focused on 1. Thickness of surfaces 2. Contact area 3....
04 May 2019 5,730 0 View
Let suppose we make a PDMS lines( 50um) on glass/PET substrate and after fully curing PDMS, we cover the PDMS lines by spin coating with PDMS and again cured the whole sample. Now, how can I...
02 March 2019 3,189 4 View
Dear members, I have a Benzyl methacrylate (monomer) and two types of crosslinkers , di(ethylene glycol) dimethacrylate (DEGDMA),poly(ethylene glycol) dimethacrylate (PEGDMA) and Carbonyl iron...
04 May 2017 6,146 4 View
Dear all, If we have 2 different shape memory polymers with different glass transition temperatures, layered one another along the thickness, then what can be expected applications? What can be...
03 April 2017 10,031 1 View
I am trying to cure my photo polymer using SL 3D printing technique, but material is not being cured by UV light of 405 nm. What type of parameters should be changed to cure my material?
31 December 2016 5,242 1 View
Dear all, I am trying to fabricate multi materials in a single process using 3D technique? what type of parameters should be kept in mind to make it more reliable?
11 December 2016 8,589 0 View
I have my own resins, how can I confirm that they are compatible for SLA and Multijet 3D printers?
10 November 2016 4,810 2 View
Let suppose, we have two type of materials, one is in liquid shape and other one is in powder shape, is it possible to make FGM type structure?? IS possible then how can we proceed?
09 October 2016 4,471 1 View
Dear researchers, How can we differentiate CNT and graphite without characterization techniques like SEM, XRD??
09 October 2016 8,514 2 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,291 2 View
Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...
06 August 2024 8,716 0 View
In my tests with a sliding mode triboelectric nanogenerator, I have observed maximum power output at three different resistance values. How should I determine which resistance provides the peak...
05 August 2024 5,049 0 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...
30 July 2024 6,137 0 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
While I am doing HER, I noticed that nyquist plots of Electrochemical Impedance Spectroscopy (EIS) is not complete. Will it affect for the Linear Sweep Voltametry (LSV) data? However, I can found...
26 July 2024 7,542 4 View
The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.
23 July 2024 3,205 0 View