How can we get average velocity of of open channel by integrating over the channel height and length?

I am following one paper about the "Electrokinetic actuation of low conductivity dielectric" but did not understand the equation 35 derivations. Can anyone please help me to find Maxwell gradient...

01 February 2020 9,439 3 View

Is it possible to get 1700 v from 25 mm^2 area from tribo nanogenerator?

I am following this paper but the results are too high to get from mentioned data? Can anyone guide me about this? Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelec...

04 May 2019 2,716 1 View

I am following one paper about Tribo Electric Nano generator but getting 10000 times less results?

I have followed all the parameters and also changed them as well. But still values are 10000 times lower than the published one. I have focused on 1. Thickness of surfaces 2. Contact area 3....

04 May 2019 5,606 0 View

How can I measure or check the adhesion( interface force) between cured consecutive layers of PDMS?

Let suppose we make a PDMS lines( 50um) on glass/PET substrate and after fully curing PDMS, we cover the PDMS lines by spin coating with PDMS and again cured the whole sample. Now, how can I...

02 March 2019 3,033 4 View

Why DMA(Dynamic mechanical analysis) results of shape memory polymers are showing odd behavior?

04 May 2017 6,024 4 View

How wave length dimension play a role in curing time for 3D printing?

I am trying to cure my photo polymer using SL 3D printing technique, but material is not being cured by UV light of 405 nm. What type of parameters should be changed to cure my material?

31 December 2016 5,130 1 View

Can we fabricate four different polymers using 3D technique?

11 December 2016 8,479 0 View

Can we use our own polymer resin for SLA and Multi Jet 3D printers?

I have my own resins, how can I confirm that they are compatible for SLA and Multijet 3D printers?

10 November 2016 4,685 2 View

Which type of methods can be used to fabricate a functionally graded polymer?

Let suppose, we have two type of materials, one is in liquid shape and other one is in powder shape, is it possible to make FGM type structure?? IS possible then how can we proceed?

09 October 2016 4,353 1 View

What is difference between graphite and CNT in terms of mechanical properties?

Dear researchers, How can we differentiate CNT and graphite without characterization techniques like SEM, XRD??

09 October 2016 8,427 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View