Is it possible to get 1700 v from 25 mm^2 area from tribo nanogenerator?

I am following this paper but the results are too high to get from mentioned data? Can anyone guide me about this? Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelec...

04 May 2019 2,716 1 View

I am following one paper about Tribo Electric Nano generator but getting 10000 times less results?

I have followed all the parameters and also changed them as well. But still values are 10000 times lower than the published one. I have focused on 1. Thickness of surfaces 2. Contact area 3....

04 May 2019 5,606 0 View

How can I measure or check the adhesion( interface force) between cured consecutive layers of PDMS?

Let suppose we make a PDMS lines( 50um) on glass/PET substrate and after fully curing PDMS, we cover the PDMS lines by spin coating with PDMS and again cured the whole sample. Now, how can I...

02 March 2019 3,033 4 View

Why DMA(Dynamic mechanical analysis) results of shape memory polymers are showing odd behavior?

04 May 2017 6,024 4 View

Whats can be expected applications of 2 different shape memory polymers layered one another?

Dear all, If we have 2 different shape memory polymers with different glass transition temperatures, layered one another along the thickness, then what can be expected applications? What can be...

03 April 2017 9,922 1 View

How wave length dimension play a role in curing time for 3D printing?

I am trying to cure my photo polymer using SL 3D printing technique, but material is not being cured by UV light of 405 nm. What type of parameters should be changed to cure my material?

31 December 2016 5,130 1 View

Can we fabricate four different polymers using 3D technique?

11 December 2016 8,479 0 View

Can we use our own polymer resin for SLA and Multi Jet 3D printers?

I have my own resins, how can I confirm that they are compatible for SLA and Multijet 3D printers?

10 November 2016 4,685 2 View

Which type of methods can be used to fabricate a functionally graded polymer?

Let suppose, we have two type of materials, one is in liquid shape and other one is in powder shape, is it possible to make FGM type structure?? IS possible then how can we proceed?

09 October 2016 4,353 1 View

What is difference between graphite and CNT in terms of mechanical properties?

Dear researchers, How can we differentiate CNT and graphite without characterization techniques like SEM, XRD??

09 October 2016 8,427 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

How can a reference point be fixed to an attachment point in Abaqus?

I am currently trying to copy an assembly feature, that is present in an old version of the model I am using, onto a new model. The feature is a reference point that is fixed to an attachment...

16 February 2021 8,872 2 View

Any way to separate out fluorescent channels from a composite image?

Hi there, I've been using the EVOS Auto II microscope for some time now and usually I will save the transmitted light/bright field image and the images from fluorescent channels as separate...

15 February 2021 546 3 View

Please, How can I plot a channel capacity of MIMO and SISO in matlab?

CSISO= f(frequency) : plot(f, CSISO) ? CMIMO= f(frequency) : plot (f, CMIMO) ?

13 February 2021 5,225 4 View

How to interface ANSYS Maxwell and Matlab?

Dear All, I am working on electric motor design in Ansys Maxwell. I have written optimization code in MATLAB. I want to run this code in ANSYS MAXWELL and generate FEA results. Does anyone know...

10 February 2021 1,279 1 View