How to use a material model of LS-DYNA which not directly availabile in ANSYS LS-DYNA ?

More Xavier Régal's questions See All

Is grammaticalization/subjectification a mechanism or motivation?

I know that we can categorize a specific linguistic change as either gramaticalization or subjectification (or both involved), but can we also say that specific linguistic change is motivated by...

31 May 2024 2,106 2 View

Could someone help a right procedure for TGA analysis of cement?

I analyzed cement samples exposed and unexposed to moisture over various periods. The TGA results of these samples showed variation with each repetition. However, I consistently used calcium...

22 May 2024 1,339 3 View

How many brain slices do we need to obtain 1 mg of protein for biochemical studies?

We are currently interested in performing a stimulation protocol on brain slices in order to perform western blotting or immunoprecipitation. However, we do not know how many 300 um slices would...

12 May 2024 6,527 1 View

Are you interested in W. Somerset Maugham?

We are organising a two-day international interdisciplinary conference on Maugham's life and works, in Le Mans, France on 13-14 March 2025. If you are interested, please read our CFP and send us...

12 May 2024 5,473 2 View

How is it possible that despite the curricular transformations, the behavioral model prevails in university education?

Due to its diversity, this turns out to be a controversial issue, since in Cuban undergraduate training, this approach is applied in a general way, transferred the pedagogical management practices...

31 July 2023 6,596 7 View

Is it possible to introduce different tabs: publications - books - conference papers - others?

Would it be possible for Research Gate personal page to place tabs to differentiate into folders such as "journal publications", "books/book chapters" and "conference papers"? It would be more...

30 July 2023 5,405 2 View

Does cyclotide-rich extract can be encapsulated into nanoparticle drug delivery system??

We identified many cyclotides with an intact mass range of 2-4kDa in cyclotide-rich extract. Can we able to encapsulate cyclotide-rich extract with 2-4kDa mass range in a nanoparticle drug...

04 July 2023 3,814 0 View

Spatial Data on Water Abstraction Points and Volumes for Europe?

Dear ResearchGate community, I am conducting a research project focused on water resource management in Europe and need access to spatial data on water abstraction points and corresponding...

15 May 2023 1,452 2 View

Can I describe a moderated effect on mediation with the moderator derived from independent variable and mediator?

Hello, In a mediation model where A is the independent variable, B the dependent variable and M the mediator, I observe the following: - when the difference between M and A is positive (based on...

13 May 2023 6,014 0 View

Hysys distillation column converges than unconverges for what reason?

Trying to understand why my HYSYS file first converges and then says it can't converge after like 5 min. Is it just rerunning the simulation and doesn't work the second time?

21 March 2023 5,223 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View