What are suitable step to reverse motion of drill bit during dental implant in abaqus ?

Hello every one. I am working on modelling dental implant and need some guidelines. I have completed the initial step for implant which is to create cavity inside a jaw. For this i have used 4 mm...

09 October 2018 7,636 4 View

To analyze the heat transfer in cement kiln which software is best ABAQUS orANSYS ?

Hello everyone. I want to simulate heat transfer in cement Kiln and to analyze different modes of heat transfer including convection , conduction and radiation. I know ABAQUS is capable of...

08 September 2018 344 3 View

To simulate heat transfer in cement Kiln which ansys module would be most compatible?

Hello every one i want to simulate the different modes of heat transfer through cement Kiln. Conductive heat transfer from clinker to inside wall of cement kiln .Convective heat transfer to...

08 September 2018 6,354 3 View

Can anyone tell me issues related to solar-wind-diesel Hybrid power system ?

Hello every one i am working on underlining issues related to solar wind diesel hybrid power system .if anyone have data related to this .please do share it with me ?

11 December 2017 9,311 13 View

To model fatigue which option should be best Fe safe or ABAQUS?

i want to model fatigue for buried pipelines.Please tell me which software should be best for modelling

07 August 2017 1,554 4 View

To model low cycle fatigue for buried Pipeline which additional properties should be defined apart from elastic ,plastic and density ?

Hello every one .Hope you will be fine i want to model low cycle fatigue in ABAQUS for buried pipeline .Please guide to model during modelling in material section which additional properties...

06 July 2017 1,736 3 View

How to apply incremental load in abaqus with load maintained for 2 minutes at each increment to monitor structure?

Hy every one i want to load the wall incrementally with rate of 0.4 kN/s. i want the load to be maintained for 2 minutes at each increment to monitor the doformation of the structure .[lease guide...

05 June 2017 6,097 7 View

How to Define amplitude curve for internal pressure of pipeline ?

How to define the amplitude curve for the internal pressure of pipelines in abaqus while using the dynamic explicit step? is it be linear curve or constant curve ?

10 November 2016 9,462 0 View

What is difference between gravity and Body force in abaqus ?

i am trying to model the stress variation in underground pipeline under traffic loading .i am trying to define the self weight of body so when i used the body force the result is different and...

01 January 1970 4,218 3 View

Can Change in thickness of X70 steel pipe has an effect on its stress strain curve?

01 January 1970 9,655 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View