How to surface sterilize the Arabidopsis leave to quantify the endophytic bacteria?

More Yu Cao's questions See All

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

Why are we measuring gel content of NBR latex? Does gel content related to the amount of cross-linked in a polymer?

Hi good day to everyone! I am actually studying the gel content of synthetic latex. Refer to ASTM 3616, gel content is measure of insoluble rubbers in the chosen solvent. So, I just would like to...

07 February 2021 605 4 View

Is it possible to keep a dusty plasma lasting a long-time without any input power?

Hi! I'm wondering is that possible as stated in the title. I think dusty plasma might be a potential candidate for energy storages, like Li battery, since the dust grains inside it could be...

09 January 2021 6,567 15 View

How to delete a copy of a paper, and how to delete a co-author's name?

I mistakenly uploaded a copy of the same paper and entered my alternative name. How to delete them out? (I couldn't navigate to the right buttons to do it. So from where to where is what I don't...

07 January 2021 7,694 6 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

What effect will different solvents have on the ATRP reaction?

I want to do an ATRP reaction, synthesize an ATRP initiator, use DMF as a solvent, and mix DMF, BIBB and TEA to turn red. Why does it turn red? Xylene has been used as a solvent before, and there...

04 January 2021 8,034 3 View

Species identification.Who can tell me the scientific names of these Gastropods?

Species identification. I've been doing research on communities of marine macrobenthos recently, but some of them can't be identified, which hinders my research. Who can help me identify these...

14 December 2020 8,357 3 View

Cell shrinkage during ROS assay(H2DCFDA)?

Hi! I'm Yu, studying about health of MSC. These days, I'm doing ROS assay with H2DCFDA which requires 5~30 minutes of staining with PBS or HEPES or HBSS. In our lab, We use PBS w/o Mg/Ca for...

13 December 2020 8,813 9 View

Can I fix the cells after H2DCFDA assay for FACS analysis?

Hi ! I'm Yu, and planning to analyze ROS assay with H2DCFDA(Thermo) on MSCs. A lot of protocols instruct that treat H2DCFDA at specific concentration for 5~30 min, 20~30 min of recovery time...

10 December 2020 973 1 View

How to reconstruct a Lamb wave by a series of pulses superposed?

Lamb wave is useful for solid structure health monitoring, and it consists many modes. Unlike ultrasonic bulk wave, when given a pulse excitation (for example, 5-cycle sinusoidal pulse), only...

08 December 2020 5,440 8 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View

How to best wash a 96-well plate containing microplastic?

I am planning my protocol for my dissertation for an experiment quantifying bacterial (E. coli) biofilm formation on micro-plastic (5mm discs of polyethylene bags) by conducting a crystal violet...

23 February 2021 7,868 2 View

Are there any known solvothermal methods to synthesize MoS2 nanosheets using solvents other than water (like ethanol/ethanol-water mixture) ?

I need to synthesize MoS2 nanosheets by alternate methods without pure water as a solvent.

22 February 2021 9,246 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Can ethanol be used as an analgesic?

If ethanol has analgesic properties, why isn't it used for clinical purposes?

18 February 2021 8,227 4 View

What is the best way to isolate Hydrolysable tannins on Sephadex column?

I am currently preparing to isolate polyphenolics (Hydrolysable tannins) from aqueous extract of a plant. I want to set up a small sephadex column to guide the major isolation on a laerge...

18 February 2021 1,455 3 View

How could the concentration from RNA extraction is really low?

Hello everyone, currently, I'm trying to do RNA extraction from seeds of Arabidopsis. I'm using the protocol below: RNA isolation from siliques, dry seeds, and other tissues of... I use about...

17 February 2021 7,583 4 View

Hi, can anybody help me with the suggestions how can I amplify a stress induced gene of 1107 bp?

I am trying to amplify the TGA1 (Transcription factor 1 ) of Arabidopsis ,which is 1107 bp. I have treated the plants with Salycylic solution over night and extracted the RNA and make cDNA. I...

17 February 2021 7,802 2 View

Muhammad Arslan

Why you are worried about damages? You anyway want to crush the plant samples for subsequent analysis...

even if you want the leave blade to be intact, use 0.1% NaClO and add tween 0.1% 20 after EtOH treatment. Make sure you check the final rinse on nutrient rich plates to study disinfection.

George Newcombe

If the plants were growing in a sterile environment why would they need to be surface-sterilized?