How to select multiple lines in ansys mechanical apdl?

Debojyoti Basu Majumder @Debojyoti-Basu-Majumder

03 June 2021 1 5K Report

During contact making procedure, I need to select multiple lines (say 100 lines) at a time. How can I select those lines through command in ansys apdl?

Soud Choudhury

Are they associated with any volume or area? You can try vsla/lsla to select lines from that area/volume. If you know the location try lsel command with loc. You need to provide more information to get specific guideline/information. Happy Researching.

Badges
Science topic

More Debojyoti Basu Majumder's questions See All

Dear Scholars, do you have the latest data (1982 to 2019/2020) of ICRG (International Country Risk Guide)?

Dear Respected Scholars, I am in need of the latest data set (1982 to 2019/20) of ICRG. I would be grateful If you share those data with me. My email address: [email protected],...

13 February 2021 2,631 1 View

What is the best analytical software for XRD data?

How can I determine any phase from the powder XRD data and how can I determine the morphous or amorphous state of the sample from XRD data?

09 February 2021 7,867 5 View

Can you suggest some plant transformation vectors that I can use for the expression of GFP/YFP-tagged protein of my interest?

I want to generate stable Arabidopsis transgenic lines expressing my protein of interest fused with GFP/YFP under the control of its native promoter. I want this for localization studies. Please...

23 January 2021 2,790 3 View

Will the wider bandgap be at the core or outer layer of radial sc?

I am simulating a radial p+AlGaAs-pGaAs- n+GaAs Solar cell. AlGaAs has the wider band gap. I want to know if and how it matters whether tha AlGaAs is at the core or the outside. I know in tandem...

06 November 2020 9,293 4 View

Queries regarding Antibody labelling ?

Hello Everyone. I was trying to label antibody with Cat# MO-L007 - Cystein reactive monolith series antibody labelling kit. I followed every steps that the protocol states. But in the final step...

26 September 2020 3,439 1 View

What if I can't find k values for n,k files in Atlas, Silvaco ?

Hello, I am looking for simulating GaAs(x)N(1-x) Material is Atlas, But I am not able to find the k values to give in the n,k index files, but I have the data for n. What should I do?

30 July 2020 7,912 2 View

How to start a small vermicompost or organic farming business and where to get funds in India?

In this time where organic farming is the best and only option for future sustainability in terms of griculture there is a need to go for biofertilizers and vermicompost techqniques and to use...

22 May 2020 5,934 14 View

Can anybody please send me MatLab code for oppotion based PSO/BBO?

Opposition based learning

05 April 2020 659 4 View

How do we calculate mechanical stress using VASP Calculations for Ab Initio Molecular Dynamics?

If we want to uniaxially strain a structure incrementally, and calculate the corresponding uniaxial stress at every strain point, how should we use the VASP output files for this purpose? I have...

04 April 2020 9,747 4 View

How can I measure the amount of essential oil and tannic acid uptake in nanoparticles like chitosan, silica by Thermogravimetric analysis (TGA)?

I want to measure the Essential oil and tannic acid uptake in nanoparticles like Chitosan, silica by TGA. Can anyone provide me a protocol for that?

14 February 2020 5,749 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View