laminar flow of water is considered
The ultrasound gel which is commercially available contains lot of air bubbles.Which creates lot of noise while scanning. How to avoid the air bubbles in the gel such that the scan wont have much...
11 December 2019 9,946 2 View
If a product is fabricated to eliminate bacteria in dress using uv lights how can we test the effectiveness of the product
08 September 2017 1,089 3 View
I am analyzing the copper water nano fluids in fluent by multi phase Eulerian-Eulerian approach.i want to describe the material properties of copper nano paricle which are dispersed in water.i...
03 April 2016 6,204 14 View
I am designing a wheel chair i want to test my design using ansys workbench harmonic response.So what are the parameters i should describe, especially the frequency range for the surface...
03 April 2016 8,893 2 View
I am doing a simulation in fluent i am using eulerian -langragian model i want to provide the material properties for secondary phase which is copper nano particle
03 April 2016 2,753 2 View
I am currently doing a project on convective heat transfer in nanofluids.my geometry is a 2D circulartube. how to specify the volume concentration of base fluid and secondary fluid in multiphase...
02 March 2016 3,060 4 View
High speed flows can be simulated with what type of solver that disregards viscosity?
01 February 2016 7,004 4 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,728 6 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,510 3 View
Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...
29 July 2024 8,624 1 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
