How to remove the air bubbles in comercially available ultrasound gel?

More Arun P Jose's questions See All

How can we test the presence of Bacteria?

If a product is fabricated to eliminate bacteria in dress using uv lights how can we test the effectiveness of the product

08 September 2017 1,089 3 View

How to specify material properties for Eulerian-Eulerian multiphase model in fluent ?

I am analyzing the copper water nano fluids in fluent by multi phase Eulerian-Eulerian approach.i want to describe the material properties of copper nano paricle which are dispersed in water.i...

03 April 2016 6,204 14 View

What will be vibrational frequency exerted by the road on the tyres?

I am designing a wheel chair i want to test my design using ansys workbench harmonic response.So what are the parameters i should describe, especially the frequency range for the surface...

03 April 2016 8,893 2 View

What is the viscosity of copper nano particles?

I am doing a simulation in fluent i am using eulerian -langragian model i want to provide the material properties for secondary phase which is copper nano particle

03 April 2016 2,753 2 View

How to specify volume concentration in ansys fluent 16???

I am currently doing a project on convective heat transfer in nanofluids.my geometry is a 2D circulartube. how to specify the volume concentration of base fluid and secondary fluid in multiphase...

02 March 2016 3,060 4 View

How to plot the fluid temperature and wall temperature of a fluid flowing through a pipe in ansys fluent 16??other than taking locations

laminar flow of water is considered

02 March 2016 8,435 0 View

High speed flows can be simulated with what type of solver that disregards viscosity?

01 February 2016 7,004 4 View

Does anyone know what might be causing the smeared bands on my western blot?

I got these smeared bands quite often lately. We typically run the gel at 140V with a 10-12% gel and do a wet transfer at 220 mA for 1.5 hr in cold room. We also noticed some dirty spots/dots (see...

10 August 2024 7,480 3 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Why is my ASO degraded quickly on agarose gel?

I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...

06 August 2024 3,130 2 View

Low-yield gel extraction problem?

I am having an issue with my gel image where my PCR product is not appearing very bright on the gel. When I perform gel extraction, the A260/280 purity value is very low. I used the Qiagen gel...

05 August 2024 9,798 3 View

PCR showing no bands - Master mix and primers didn't mix?

Hello everyone, I performed a PCR yesterday, and the results showed no bands on the gel. Of course, I probably missed some crucial steps, like adding my samples to the PCR strips themselves, for...

31 July 2024 2,406 6 View

How to check pH of a high strength hydrogel?

We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...

30 July 2024 942 2 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

What is the relationship between the threshold voltage and the device's noise performance, particularly in terms of flicker noise and thermal noise?

The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...

29 July 2024 3,246 0 View

Why my IgG antibody looks fragmented on non-reducing SDS-PAGE?

I am performing IgG purification and I have to show my results on SDS-PAGE. I use 10% tris glycine gel and prepare the samples under non reducing conditions. I am new to antibodies and therefore...

23 July 2024 6,664 6 View

What is the cause of this aggregation just bellow 70 kDa mark?

Hello, I was running a 12% SDS Page electrophoresis on few granulosa cell samples and got this result after the ponceau staining. The total protein lysate seem to aggregate at 70 kDa ladder mark...

21 July 2024 5,128 4 View

Moawia Bushra Gameraddin

In general, the air-bubbles are removed when with carefull probe handling during the scanning when the probe is being well closed on the skin.

Mithun Kuniyil Ajith Singh

Hello Arun,

In a research-setting, we used to centrifuge the gel for removing all bubbles. Hope it helps!

Cheers,

Mithun