How to plot Load-Elongation or Stress-Strain plot in ANSYS APDL 18.2 for ball indentor process ?

04 April 2018 0 9K Report

Hello Everyone,

Can someone help me in this regard?

I am simulating ball indentation process for PZT material taking WC as an indentor. I am able to get all my results except, load vs penetration depth curve.

So could anyone of you please help me ?

Please give detail explanation or any video will be helpful for me.

Please do needful. It's quite urgent.

Thank You !!!

Badges
Science topic

More Vaibhav S Kathavate's questions See All

Penetration Error in Indentation in ABAQUS?

Dear all, I have done indentation simulation in Abaqus for that i am taking indenter as rigid body and specimen as deformable body also I gave indenter as master surface, specimen as slave...

08 September 2018 6,667 2 View

How can I couple the degrees of freedom in ABAQUS?

Hello Everyone, I intend to carry out piezoelectric simulations in ABAQUS. For that I am coupling mechanical and electrical field. But the problem is how to couple electric voltage (EPOT) between...

08 September 2018 7,833 4 View

How to apply incremental stepped loading in APDL?

Hello Everyone, I am doing indentation process in APDL. For that I propose to apply total of 1500 N load divided in 6 cycles. I want load-deformation curves through APDL. So does anybody has an...

07 August 2018 8,832 0 View

Modelling of Berkovitch Indenter in Abaqus?

Does anybody has an idea about modelling the berkovitch indenter in abaqus (3-D)?

07 August 2018 7,043 2 View

How to plot Load-Elongation or Stress-Strain plot in ANSYS APDL 18.2 for ball indentor process ?

Hello Everyone, Can someone help me in this regard? I am simulating ball indentation process for PZT material taking WC as an indentor. I am able to get all my results except, load vs...

03 April 2018 1,258 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View