How to plot contour of model at each dytime in flac2d ?

26 October 2023 1 2K Report

I use the FLAC2D 7.0. and, tried some analysis of model. But, I can draw the contour plot at dytime of end only. I wonder if i can plot the contour at each time using basic flac system not using fish code like FLAC3D. Does anyone know this?

Alireza Rashiddel

You can solve with different times, foe example:

Solve dytime 0.1

save dytime0.1.sav

;and

Solve dytime 0.2

save dytime0.2.sav

;and

Solve dytime 0.3

save dytime0.3.sav

...

Solve dytime 10

save dytime10.sav

More Juseung Ryu's questions See All

Troubles about using high pressure homogenizer (Emulsiflex B15)?

I have some trouble while using the Emulsiflex B15. Since last week, if i turn the air control knob to fill the sample inside the homogenizer, the sample does not enter well. And even if it...

04 March 2024 7,574 1 View

How can i deoxygenate oxyhemoglobin solution using nitrogen gas?

I want to deoxygenate oxyhemoglobin with nitrogen bubbling, but i can't observe the characteristic peak of deoxyHb in UV-Vis spectrum. Also, the concentration of my hemoglobin sample was little...

01 January 2024 5,512 0 View

How can i degas the sepharose gel?

I'm going to experiment with sepharose CL-4B gel to isolate drugs that are not enclosed in liposomes. I need to degas enough before using the sepharose gel, and most of the references seem to be...

20 August 2023 5,827 1 View

What are the possible reasons of increasing peak intensity of certain plane while all other peak intensities decrease in XRD pattern?

I prepared thin PDMS film embedded with CsPbBr3 Perovskite quantum dot and doped Ag+ ions to PQDs inside PDMS. The XRD results showed that the peak intensity of (100) plane increased while...

13 April 2023 3,692 4 View

Did you know that Convergence of the PM4SAND model in FLAC2d ?

I tried the static analysis of the model using PM4SAND in FLAC 7.0. But It had a weird unbalanced force curve. Initially, It seems that there is a problem with the geometry model, but other...

26 January 2023 2,019 2 View

How can i solve defects(comet, pinhole) on coated photoresist?

Hello, I'm going to spin coat PR on ITO Glass. But my process, After the spin coating, holes are formed in the photoresist. So I can`t proceed with the next process(Develop, Etching ...) The...

08 January 2023 5,958 3 View

Problems with photoresist patterning and Development ?

Hello. I want to make an pattern on the ITO glass. I attached a picture of my experiment process and results. A problem occurred in the process of PhotoResist development. When I spray AZ300 MIF...

26 December 2022 6,773 3 View

How to consider dynamic pore pressure in FLAC2D 7.0 ?

I want to see the excessive pore pressure's time series and variations. In FLAC 2D 7.0, I can apply the water by table and It can't use in set GWflow. But, soil porosity and permeability can input...

11 December 2022 7,483 2 View

Why does the elution order change depending on the mobile phase in chromatography?

Sorry for asking such a basic question... When analyzing flavonoids or cannabinoids, i saw that the use of ACN and MeOH changed the elution order of the components. In RP-condition, isn't it that...

04 December 2021 9,744 3 View

How do we know that feasible solution is found at boundary point?

how can i prove that mathematical proof about feasible solution is found at boundary point? also want to ask about why feasible region must be composed of a convex set. is there any mathematical...

17 November 2021 2,634 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Why does everyone use vs code?

Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...

07 August 2024 7,013 4 View

Is an invitation to join the editorial board of Clinical Cardiology Updates a scam?

I received an e-mail invitation to join the editorial board of Clinical Cardiology Updates. While I have published a few articles related to cardiovascular disease, there are lots of colleagues...

06 August 2024 8,981 8 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Can anyone please provide me the full text article of this clinical Trial?

Roflumilast Cream Improves Signs and Symptoms of Plaque Psor...

29 July 2024 5,250 0 View

What is your major research area?

My major research area is clinical research and basic research of thyroid and parathyroid.

26 July 2024 3,639 14 View

All math can be explained by iterator of code?

all math can be traversed by code? all math can be translate to code?

26 July 2024 9,530 0 View

How can i solve the code problem in Sentaurus TCAD?

Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...

24 July 2024 6,352 0 View