How to model SLM (Single Level Modeling) and Theoretically modeling of transport?

02 December 2024 0 2K Report

I like to know the complete theory behind SLM (Single Level Modeling) and Theoretically modeling of transport and all the essential required parameter.

Badges
Science topic

More Vikash Meghwal's questions See All

Sadhana journal follows which reference style ?

sadhana journal follows which reference style ?

24 September 2023 4,520 1 View

How can I guarantee the accurate measurement of Vickers microhardness?

The indentation produced on the surface by the indenter in the attached image does not exhibit a square shape, and its diagonal lengths are unequal. It's worth noting that Vickers microhardness...

12 September 2023 9,482 7 View

Why is my purified GST protein binding to Ni-NTA beads?

I am trying to find interaction between two purified proteins .For that I am taking purified GST protein as a negative control,since GST should not bind to NI-NTA agarose beads.But after...

30 July 2023 6,533 0 View

Kaempferol maximum solubility ?

My problem is related to kaempferol solubility and their precipitate formation. 1. When I try to dissolve kaempferol in DMSO it was dissolved but later when I further dilute the stock solution...

08 May 2023 7,893 0 View

How to distill N,N- Dimethyl Formamide DMF?

I wanted to know procedure and mechanism for the distillation of Formamide,, N-methyl Formamide, N,N- Dimethyl Formamide DMF. and drying procedure.

26 January 2023 1,685 2 View

The stability of the material is important for the electrocatalysts. What is the stability of the catalyst material before and after the reaction?

How we describe the stability of the catalyst before and after the reaction?

04 November 2022 7,232 2 View

UDFs for Diffusion of liquids through the porous wall (Ansys Fluen) ?

I am working on the interdigitated flow channel, where mating surfaces (internal) are supposed to diffuse the liquids (water and ethanol) from one side to the other. I experimented with different...

20 September 2022 4,781 0 View

Why is there a difference in the roughness value measured by the surface profilometer and AFM?

I am getting different roughness values for same sample surface by Taylor Hobson surface profilometer and AFM. Approximately half the roughness value coming in case of AFM as compared to surface...

11 May 2022 2,374 2 View

How do I simulate a multi-BS 5G network in NetSim?

I need to do a system-level simulation of a 5G network where I can define parameters like location/mobility of UEs, channel models for pathloss/shadowing/fading, handover parameters such as time...

30 December 2021 9,106 12 View

How to complete education PG level degree projetc, when everything is closed due to CORONA pandemic and labs are closed?

What can be possible ways to complete the requirement of PG level final year projects in on Food science, food nutrition and food technolgy, with quality work under such crucial time of pandemic...

23 June 2021 669 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View