adding graphene oxide / rGO / graphene have shown conflicting surface roughness changes in Polyethersulfone. for rGO in specific, why do we have roughness decrease whilst porosity has increased?
Hi,
Please find the attachments; they might be useful for you
[1] https://pubs.rsc.org/en/content/articlelanding/2015/ra/c5ra11349k#!divAbstract
i am interested
several nanoadditives can decrease the molecular mobility of polymers, and this can affect the surface roughness.
https://pubs.acs.org/doi/10.1021/acsami.7b06420
https://journals.aps.org/prapplied/abstract/10.1103/PhysRevApplied.9.024018
https://www.nature.com/articles/srep13562
The link for article can help
https://pubs.rsc.org/en/content/articlelanding/2015/ra/c5ra11349k/unauth
It may be attributed to that rGO is decreasing the affinity for non-solvent during phase inversion.
check this article
Article High flux and fouling resistant flat sheet polyethersulfone ...
GO in NMP - considering NMP is not an electrilyte on itself, can the flakes move towards the opposite electrode?
08 September 2018 9,349 0 View
when the loadings of GO in the polymer increased the contacact angle was almost the same as the pure polymer and in one case higher... what can be the reason ... it is expected to have more...
04 May 2018 8,063 3 View
when I apply an electric field over my polymer solution it tries to move toward the negative electrode (the distance between the two electrodes is very low) this local movement is different every...
02 March 2018 10,092 4 View
while casting a carbon filler /polymer composite membrane on glass, during inversion in water , it gets up with a convex surface which is a little shiny. is this side the top surface of the...
01 February 2018 8,022 9 View
when i want to try thick sectioning of my sample, I fill in the tray with water bu even with angular and axial regulations and also filling and vacuuming water , it does not wet the upper part !...
31 December 2017 6,494 6 View
I need to cover a metal surface with a thin layer of a water soluble polymer and this layer should adhere very well and not separate , also no-toxic ... what are the feasible methods?please...
31 December 2017 3,747 10 View
I need to know the viscosity and dielectric of my solution. (polymer in a polar solvent)please advise if there is simple models or estimation techniques just to know an approximate estimation
31 December 2017 6,046 2 View
my membranes are produced about 4.5 cm . is it possible to test them by a sterlitech HP4750 cell with some modifications of the setup?
11 December 2017 3,862 2 View
when we are using phase inversion method, how can we avoid formation of holes in the film casting on a glass slide? what parameters are effective?
09 October 2017 4,788 1 View
I want to make a gold electrode through sputtering to get a very good, flat and smooth conductive electrode. but I do not know the condition of operation.... do you know what parameters are...
08 September 2017 4,237 7 View
Hello experts, Does anyone know any free software about retention index prediction ?
08 August 2024 7,403 2 View
I am trying to analyse data from a survey examining what variables affect teachers perceived barriers to incorporating technology into their classroom. I have 5 predictor variables however my DV...
06 August 2024 1,752 3 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
Hi I am working on data driven model of the microgrid, for that, i need the reliable datasets for the identification of MG data driven Model. Thanks
02 August 2024 5,748 4 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...
01 August 2024 4,606 7 View
what is the best research evidence for psychological interventions for Bipolar?
01 August 2024 6,023 2 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View