How to evaluate the accuracy of non-uniform stress measured by blind hole meter?

09 March 2020 0 2K Report

Residual stress is widely found in various parts. The neutron diffraction method is relatively accurate, but the experimental conditions are limited.

Badges
Science topic

More Kaixuan Gu's questions See All

Questions of antibodies selection?

Hi there, I'd like to use immunocytochemistry to determine a surface protein expression on mouse cell. The primary antibody I have is mouse anti mouse, and the secondary antibody I have is goat...

15 July 2024 6,008 5 View

How to do single-trial ERP analysis?

Single-trial ERP analysis provides a way to extract the amplitude of each trial rather than one certain condition...

01 July 2024 6,553 2 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View

Research on academic research in Canada?

What Canadian university teams are doing medical image processing or gastrointestinal endoscopic image processing based on deep learning technology?

13 April 2024 6,974 1 View

Is there a rapid method to determine the agar content in microalgae?

Traditional methods for the determination of agar content in macroalgae need a lot of time, if there is a fast and accurate agarine content detection method will greatly promote the development of...

21 March 2024 3,306 0 View

Is it possible to do the 1-1-2 multilevel model in R?

I am constructing a multilevel model. To specify, I have two independent variables, one in Level 1 and another one in Level 2. The moderate variable and dependent variable are both in Level 2....

25 February 2024 9,874 3 View

How can I calculate the ICC1, ICC2 for each company?

I have a dataset that includes 1900 companies. Also, I investigated 10 employees for each company. There is a question about the risk preference of each employee. At now, I need to calculate the...

13 December 2023 9,571 5 View

Did someone used E. coli cell-free system in 384 plate?

I'm gonna do the E. coli cell-free experiment in 384-well plate. But I have trouble with plate choice. E. coli cell-free experiment doesn't need a sterile enviroment, but I think plate should be...

12 November 2023 1,990 0 View

Anomalous initial charging behavior of LiFePO4 half cell assembled with Li metal?

Hello! I just started learning battery research. I'm working on to get myself used to coin cell assembly process and to achieve reproducibility of sample preparation. Here's my coin cell...

11 October 2023 868 2 View

Does repeated use of agarose gels affect the pre-staining gelred in the gel?

I only used 2 wells of 12-well gel for my first electrophoresis. Can I reuse the remaining wells at the end of this electrophoresis? Could the gelred dye in the gel have been affected by the...

20 September 2023 9,803 1 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,291 2 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View

Can anyone guide me the best method to analyze the XRD data???

I will be doing an XRD on a sample which is powdered in natured and is a hydrogenated compound. I would like to know how we can understand the individual components and components by using the...

28 July 2024 4,548 2 View

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

How do nutrient transporters and aquaporins interact under abiotic stress in plants?

"The Correlation between Nutrition and Transport Mechanism under Abiotic Stress in Plants: A Comprehensive Review" by Muhammad Saleem, Jianhua Zhang, Muhammad Qasim, Rashid Iqbal, and Li Song,...

23 July 2024 9,109 0 View