Hello, regarding Mxene 2D titanium carbide?

More Wedad A. Alwesabi's questions See All

Hello, please if any researcher work in ion battery help me,?

I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture

14 July 2024 7,701 2 View

Please, give me the correct syhtesis process for hbn and what is the raman range for h-BN ?

I prepared h-BN by hydrothermal methods by boron anhydride and urea after hydrothermal I was heated at 800 temps for 12 hours after that my sample stuck to the crucible the third time, and the...

15 May 2024 7,353 0 View

Hello, what the value of Id/Ig ratio for graphene oxide should be?

i prepared graphene oxide by modified hummers method

13 May 2024 5,160 2 View

Hello, I need to ensure that my calculation for the amount of ZnO-TiO2 nanocomposite is right or is there a mistake, or there is another way?

I fabricated nanocomposite using the sol-gel method with a mole ratio (1:1) I want (10g) of the final product ZnO-TiO2( molar mass-161.246g/mol) the calculations of the raw materials are as...

13 May 2024 1,730 5 View

Please, is it important to convert MgO nanoparticle powder to pellet for getting peaks of Raman spectrum?

MgO NPs were synthesized by sol-gel method. i got Raman peaks at 1022 and 1400

09 May 2024 1,025 3 View

What are starting material for hBN powder synthesis ?

I need this synthesis by hydrothermal method

06 May 2024 1,865 4 View

Hello,I prepared MgO NPs by sol-gel method, for raman spectroscopy what range should i use? because i used (100-900) but there is no peak?

Actually, I prepared a large amount of MgO, after aging I kept it in a hot air oven at 120 for 12 hours, but there was still moisture there, then I kept it again in a hot air oven at 120C for 6...

05 May 2024 6,278 2 View

Which type of laser and laser power appropriate for Raman for magnetite Fe3O4?

because I prepared magnetite by sol-gel method, I got XRD peaks, but for Raman, I didn't get a peak at the range 600cm-1, should I change the wavelength of the laser, or what do I have to do

05 May 2024 2,243 4 View

Hello, please , can we use the microwave oven which used in kitchen for drying the sample instead of the hot air oven?

microwave

16 April 2024 10,005 4 View

Why the sample get evaporation when keeping it in tube furnace with Ar gas?

rGo by heating GO sample is getting out by tube

02 April 2024 1,719 1 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,080 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 724 3 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,288 2 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,196 4 View

How to calculate the molar proportions of the oxides from the XRF analyses?

02 August 2024 2,558 2 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,259 4 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

IHC profiler in image j software. has anyone used it to quantify nuclear DAB positivity?

Dear researchers. I tried using the IHC PROFILER in image j to quantify nuclear DAB staining. I followed the instructions in the original article by "Varghese F, Bukhari AB, Malhotra R, De A...

29 July 2024 2,228 0 View

While using the IHC PROFILER plugin in image j software, to quantify the epithelial cytoplasmic DAB staining do you crop remove the stromal tissue?

My question pertaining to the DAB staining in cytoplasm of human oral squamous cell carcinoma tissue. When quantifying the epithelial cancer cells do we have to crop remove the stromal tissue?...

29 July 2024 2,682 6 View

Şükrü Aktaş

Doğru işlem

Wedad A. Alwesabi

Şükrü Aktaş thank you

Simonas Ramanavičius

Dear Wedad,

you can find multilayered Ti3C2Tx MXenes XRD patterns in these papers:

Article Monitoring Ti3C2Tx MXene Degradation Pathways Using Raman Spectroscopy

Article Selective Enhancement of SERS Spectral Bands of Salicylic Ac...

Article Electrochemical real-time sensor for the detection of Pb(II)...

Your XRD pattern has some similarities to MXenes; however, the MAX phase quality and pretreatment can significantly influence your synthesis products. I suggest using Raman spectroscopy and scanning electron microscopy to investigate the synthesis products and ensure MXenes' quality.

Simonas Ramanavičius thank you