I want to simulate shear loading in rectangular plate in ANSYS apdl. how to apply load and boundary conditions in ansys?
Place SURF153 elements in 2d case or SURF154 in 3D over the surface of the elements where you want to apply shear loads to. These elements allow applying all components of surface loads.
thank you sir for your attention and guidance.
sir i want to simulate pure shear problem in ansys. sir could you elaborate procedure. how to define elements?
Ok, Piyush
Please, see the APDL script attached. It contains the model in plane strain formulation.
thanx alot sir...
apply this boundary conditions :)
I am comparing solutions of linear elastic response of a material in Abaqus explicit with inbuilt model and with VUMAT (Linear Elastic) code on single element. I am getting almost same results...
08 September 2019 8,296 2 View
I am doing fatigue damage analysis of composite in Abaqus. How to simulate high number fatigue say 10K or 20K cycles in abaqus, since it is not feasible to simulate each cycle due to high...
04 May 2018 1,026 2 View
I have created .RPT in Abaqus but when I open the file it doesn't contain any proper data and most of the columns have NO VALUE. I would be thankful if anyone can provide the procedure to export...
06 July 2017 1,220 13 View
In research articles term 'normalized stress' or Normalized modulus is frequently used. What is normalized stress or modulus? And what is its significance?
31 December 2016 6,290 0 View
looking for design guidelines of striker mechanism or gas gun mechanism of split hopkinsor pressure bar. what are the parts of launching system and what instrumentation is required?
10 November 2016 8,606 0 View
some study material for FEM of ceramic matrix composites
09 October 2016 2,804 2 View
can anyone suggests procedure to perform FEA of ceramic matrix composites?
09 October 2016 3,560 3 View
how to define orientation of layers and what should be thickness of cylinder?is it equal to thickness of layers? what should be boundary conditions when internal pressure is applied?
04 May 2016 5,222 5 View
plate dimension 100*100mm, material graphite/epoxy, stacking sequence (0/90/0/90/0/90/0) ply thickness=1/7, total thickness of laminate=1mm , applied stress=1MPa, but after solving the problem...
04 May 2016 5,259 5 View
what is the meaning of 95,181,281 in SOLID95, SHELL181 and SHELL281?
04 May 2016 6,850 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View
I am using gelatin to model mechanical properties of brain tissues in-vitro. Do you have any suggested concentration ? Thank you so much.
19 July 2024 3,095 0 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View