what is the meaning of 95,181,281 in SOLID95, SHELL181 and SHELL281?
These are the item nos. as allotted by ANSYS for the identification of element types available in its library. Just open the ANSYS help menu and type solid186, shell91, shell181,281 etc you will understand the underlying idea.
I am comparing solutions of linear elastic response of a material in Abaqus explicit with inbuilt model and with VUMAT (Linear Elastic) code on single element. I am getting almost same results...
08 September 2019 8,296 2 View
I am doing fatigue damage analysis of composite in Abaqus. How to simulate high number fatigue say 10K or 20K cycles in abaqus, since it is not feasible to simulate each cycle due to high...
04 May 2018 1,026 2 View
I have created .RPT in Abaqus but when I open the file it doesn't contain any proper data and most of the columns have NO VALUE. I would be thankful if anyone can provide the procedure to export...
06 July 2017 1,220 13 View
In research articles term 'normalized stress' or Normalized modulus is frequently used. What is normalized stress or modulus? And what is its significance?
31 December 2016 6,290 0 View
looking for design guidelines of striker mechanism or gas gun mechanism of split hopkinsor pressure bar. what are the parts of launching system and what instrumentation is required?
10 November 2016 8,606 0 View
some study material for FEM of ceramic matrix composites
09 October 2016 2,804 2 View
can anyone suggests procedure to perform FEA of ceramic matrix composites?
09 October 2016 3,560 3 View
how to define orientation of layers and what should be thickness of cylinder?is it equal to thickness of layers? what should be boundary conditions when internal pressure is applied?
04 May 2016 5,222 5 View
plate dimension 100*100mm, material graphite/epoxy, stacking sequence (0/90/0/90/0/90/0) ply thickness=1/7, total thickness of laminate=1mm , applied stress=1MPa, but after solving the problem...
04 May 2016 5,259 5 View
04 May 2016 3,327 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I want to know more about REE deposits.
03 August 2024 6,930 2 View
31 July 2024 7,366 1 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
How to assign allele numbers and sequence type after amplifying housekeeping genes by PCR for genotyping of S. pneumoniae strains by MLST using bioedit ?
19 July 2024 5,239 2 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
01 July 2024 6,680 2 View
We aim to study an exothermic process and evaluate its temporal changes. Could you recommend suitable software for this purpose and explain how to conduct this analysis? What specific data is...
30 June 2024 8,413 1 View