How to define the boundary nodes from Gmsh mesh file?

04 May 2020 1 7K Report

I am new to Gmsh and I have a problem on how to find the boundary nodes from mesh file.My mesh file and model are given below.

Abhishek Singh

While generating geometry, they allow you to tag geometrical entities such as boudaries, domains etc. by name. After which, you can use them for preprocessing of simulation.

Badges
Science topic

More Spyros Asrva's questions See All

Why different meshes give total different results in Abaqus model?

I am studying a 2D model for ideal plastic case.I am confused why different element size gives different results,I know that more elements give better results but at least the results should be...

08 September 2019 774 9 View

Is there the possibility to detect a specific aminoacid sequence from proteomic data?

I am planning to LC/MS experiment to characterize the proteome of a specific biological fluid. I am mainly focused on detecting specific cleaved isoforms of my protein of interest. Is there any...

31 March 2019 9,846 3 View

Does hourglass instabilities exists in a Q4 elements with 2 Gaus points?

Does hourglass instabilities exists in a Q4 elements with reduce integration using 2 Gaus points?

19 February 2019 6,045 7 View

How to increase continuity in FEM?

My question is how to increase the continuity of displacements in case of truss or plane elements. For example from C0 continuity to C1.Is this possible?

22 January 2019 5,527 4 View

How to determine the load vector?

I have a problem in how to determine the load vector in this problem.My question reffers to the load vector with maximum value q1 which is applied inside the 4node finite element.(q0 is applied on...

10 January 2019 7,491 7 View

How to take stiffness and mass matrices from sap2000?

i am working on a project using sap2000 and i need to take stiffness and mass matrices and pass them to matlab

27 February 2018 8,533 6 View

Equivalent stress in a finite element model

I am writting a code to simulate elasto-plastic behaviour of a 2D plane stress model.The finite element discretization is based on quadrilateral elements.My question is based on calculation of...

01 January 1970 4,955 5 View

How to implement elastodynamics in abaqus

I am familiar using abaqus for solving static FE problems but how can I implement a linear elastodynamic model in abaqus? I want to test how displacements are changing in time when a...

01 January 1970 7,297 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View