Hey guys I want to ask a question regarding the BC's on this pipe.Should I fix only the face of the flanges or the whole flange?Also,should I fix the bolt holes?
Thank you very much
It depends on how accurate you want your solution
If you don't need an accurate solution near the flange, then you can fix the face.
If you need an accurate simulation of the flange then use a spyder remote connection with springs on each bolt.
During the fabrication of CsPbI3 LEDs with ZnO as ETL and TFB as HTL, I deposited Au on top of the TFB layer. However, upon measuring the devices, there was no photoresponse observed. Is it...
02 May 2024 4,741 1 View
Dear Everyone, I am new to the concept of material science. I tried to simulate a solidification process of 7079 alluminium alloy using Scheil-Gulliver method in Matcalc. However, I noticed that...
01 February 2024 6,976 1 View
I have created a solid mesh of a flange model in hypermesh. However, only one of the mesh quality criteria is not satisfied. The max angle of some hexahendral elements is slightly higher than 135°...
23 November 2022 5,572 3 View
I am new to Gmsh and I have a problem on how to find the boundary nodes from mesh file.My mesh file and model are given below.
03 May 2020 6,996 1 View
I am studying a 2D model for ideal plastic case.I am confused why different element size gives different results,I know that more elements give better results but at least the results should be...
08 September 2019 905 9 View
I am planning to LC/MS experiment to characterize the proteome of a specific biological fluid. I am mainly focused on detecting specific cleaved isoforms of my protein of interest. Is there any...
31 March 2019 9,998 3 View
Does hourglass instabilities exists in a Q4 elements with reduce integration using 2 Gaus points?
19 February 2019 6,167 7 View
Sorry for my silly qustion but I am a little bit confused on how to determine load vecto in fem.My question is when do we include reaction forces in nodes to our load matrix? For example in this...
26 January 2019 4,163 0 View
My question is how to increase the continuity of displacements in case of truss or plane elements. For example from C0 continuity to C1.Is this possible?
22 January 2019 5,662 4 View
I have a problem in how to determine the load vector in this problem.My question reffers to the load vector with maximum value q1 which is applied inside the 4node finite element.(q0 is applied on...
10 January 2019 7,688 7 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...
01 August 2024 9,903 7 View
I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...
31 July 2024 1,123 4 View
i need to know what the key factors that the freshers are facing to get into the recruitment process, explain me clearly
31 July 2024 6,872 2 View
What challenges do you think businesses or entities face in implementing these strategies? Thanks
28 July 2024 2,125 14 View
I isolated microbial DNA from marine water samples taken at various sites using the Qiagen Power Water DNA Isolation Kit, including a modified enzymatic lysis step. I encountered a situation where...
24 July 2024 9,688 0 View
how to fix this error, from phq_readin : error # 1 DFPT with the Blochl correction is not implemented I am attaching my ph.in file.
23 July 2024 4,649 2 View
I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...
20 July 2024 1,440 3 View
> library(meta) Error: package or namespace load failed for ‘meta’ in loadNamespace(i, c(lib.loc, .libPaths()), versionCheck = vI[[i]]): there is no package called ‘numDeriv’
18 July 2024 3,536 0 View