How to define load vector in linear FEM?

27 January 2019 0 4K Report

Sorry for my silly qustion but I am a little bit confused on how to determine load vecto in fem.My question is when do we include reaction forces in nodes to our load matrix?

For example in this case should i include the reactions to?

Badges
Science topic

Similar topics
Mathematics
Algebra
Matrix

More Spyros Asrva's questions See All

Is it necessary to add MoO3 on top of TFB (HTL) in order to measure red PeLEDs such as CsPbI3 and FAPbI3?

During the fabrication of CsPbI3 LEDs with ZnO as ETL and TFB as HTL, I deposited Au on top of the TFB layer. However, upon measuring the devices, there was no photoresponse observed. Is it...

02 May 2024 4,741 1 View

Solidification of 7079 aluminium alloy?

Dear Everyone, I am new to the concept of material science. I tried to simulate a solidification process of 7079 alluminium alloy using Scheil-Gulliver method in Matcalc. However, I noticed that...

01 February 2024 6,976 1 View

Mesh quality metrics?

I have created a solid mesh of a flange model in hypermesh. However, only one of the mesh quality criteria is not satisfied. The max angle of some hexahendral elements is slightly higher than 135°...

23 November 2022 5,572 3 View

How to define the boundary nodes from Gmsh mesh file?

I am new to Gmsh and I have a problem on how to find the boundary nodes from mesh file.My mesh file and model are given below.

03 May 2020 6,996 1 View

Why different meshes give total different results in Abaqus model?

I am studying a 2D model for ideal plastic case.I am confused why different element size gives different results,I know that more elements give better results but at least the results should be...

08 September 2019 905 9 View

Is there the possibility to detect a specific aminoacid sequence from proteomic data?

I am planning to LC/MS experiment to characterize the proteome of a specific biological fluid. I am mainly focused on detecting specific cleaved isoforms of my protein of interest. Is there any...

31 March 2019 9,998 3 View

Does hourglass instabilities exists in a Q4 elements with 2 Gaus points?

Does hourglass instabilities exists in a Q4 elements with reduce integration using 2 Gaus points?

19 February 2019 6,167 7 View

How to increase continuity in FEM?

My question is how to increase the continuity of displacements in case of truss or plane elements. For example from C0 continuity to C1.Is this possible?

22 January 2019 5,662 4 View

Boundary conditions on a flanged pipe?

Hey guys I want to ask a question regarding the BC's on this pipe.Should I fix only the face of the flanges or the whole flange?Also,should I fix the bolt holes? Thank you very much

12 January 2019 3,587 1 View

How to determine the load vector?

I have a problem in how to determine the load vector in this problem.My question reffers to the load vector with maximum value q1 which is applied inside the 4node finite element.(q0 is applied on...

10 January 2019 7,688 7 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

How to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field in Techplot?

Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You

02 August 2024 3,615 1 View

What can i do to find the right topic for my thesis?

i am facing the difficulty to find the right and latest topic for my thesis. i searched and read hundreds of articles but i couldn't find the right one. what can i do I'm really confused.

02 August 2024 1,323 8 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View