How to define different values of fracture for each mode using the mode independent principle in abaqus ?

More Pandi Pitchai's questions See All

What are first, second and third cracks (red, green&blue color outline) in crack pattern of RC beams in ANSYS APDL?

Hello everyone, Can anyone kindly explain what is mean by three different colours of cracks in RC beams in ANSYS APDL and the features of first crack (red colour outline) second crack (green...

17 November 2020 2,512 1 View

Having an issue with defining sub caption in the Springer LaTeX file ?

Dear All, I am facing defining the sub caption issue in the Springer LaTeX file. If I define the sub caption in the Tex file, it exhibits an error while compiling. In general, Springer, LaTeX...

17 October 2020 6,473 2 View

What should be reason for higher values of Ultimate results for RC beam simulations in ANSYS APDL?

My RC beams experimental ultimate load & deflection was 97kN and 20mm resp. But when I model it in ansys apdl it run continuously up to a load of 140kN and 60mm deflection and still...

02 October 2020 8,747 2 View

Why the solution runs continuously even after reaching ultimate strength of beam in ANSYS APDL?

I am analyzing RC beam in APDL and tried convergence criteria with F=0.05 once then U=0.05 and also tried both criterias simultaneously but what I found is my solution continuous even upto twice...

02 October 2020 1,490 2 View

Need "E.Hognestad;" compressive stress-strain curve explanation?

Can anyone kindly explain in case of Hognestad compressive stress-strain curve for concrete, they have given fc" =0.85fc', but why researchers are use fc"=fc' instead. Where fc" =ultimate...

14 August 2020 7,508 3 View

How to check stress in main steel at first crack, yield load and ultimate load in ANSYS APDL?

good morning everyone, i need your help once again, As i am analysing RCC Simply supported beam in ANSYS APDL. i run the model upto ultimate failure, now i want to check the stresses in steel bars...

12 June 2019 7,168 3 View

How to model over reinforced section to check the failure mode?

i model a beam as Over Reinforced Section (ORS), Ast > Ast,lim), using solid65, link8 and solid45 in ANSYS APDL V12, used '"MISO" property to concrete (M20) for stress strain curve, to model...

04 June 2019 9,581 4 View

What is the concept of shear transfer open and close coefficient in ansys apdl and how it affects the load deflection behaviour of concrete & crack?

plz see the MS word file attached below and suggest your valuable answer plz.

22 April 2019 5,650 3 View

How to get rid of short piece of DNA contamination in the gel filtration column?

Dear all, I am looking for some help regarding DNA contamination. Before inject my protein sample and I normally treat them with Benzonase, but these days the protein recovery from gel...

22 March 2018 3,264 4 View

How to get the antibody for hight molecular weight protein 250KD to work?

I'm working on T type calcium channel. I have knockout the t type calcium channel isoform by CRISPR cas9 method. At the DNA level, I could see the shifted band in the agarose gel in comparison...

05 September 2017 8,809 8 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View

Pandi Pitchai

I planning to perform sensitivity study by varying fracture energy for each mode case, in order to determine which mode is prevailing the fracture phenomenon in the model. This study will be demonstrated considering pure mode independent behavior using the principle of mode independent behavior but unfortunately, in ABAQUS, there is no option any option to define the different value of fracture particularly while using this mode independent context. Therefore, in such case, is there any option to different values of fracture energy in ABAQUS (mode independent case).

Hi,

I am sorry, have not find any useful information related to my question from the suggested paper.

Thank you