What are first, second and third cracks (red, green&blue color outline) in crack pattern of RC beams in ANSYS APDL?

Hello everyone, Can anyone kindly explain what is mean by three different colours of cracks in RC beams in ANSYS APDL and the features of first crack (red colour outline) second crack (green...

17 November 2020 2,512 1 View

What should be reason for higher values of Ultimate results for RC beam simulations in ANSYS APDL?

My RC beams experimental ultimate load & deflection was 97kN and 20mm resp. But when I model it in ansys apdl it run continuously up to a load of 140kN and 60mm deflection and still...

02 October 2020 8,747 2 View

Why the solution runs continuously even after reaching ultimate strength of beam in ANSYS APDL?

I am analyzing RC beam in APDL and tried convergence criteria with F=0.05 once then U=0.05 and also tried both criterias simultaneously but what I found is my solution continuous even upto twice...

02 October 2020 1,490 2 View

Need "E.Hognestad;" compressive stress-strain curve explanation?

Can anyone kindly explain in case of Hognestad compressive stress-strain curve for concrete, they have given fc" =0.85fc', but why researchers are use fc"=fc' instead. Where fc" =ultimate...

14 August 2020 7,508 3 View

How to check stress in main steel at first crack, yield load and ultimate load in ANSYS APDL?

good morning everyone, i need your help once again, As i am analysing RCC Simply supported beam in ANSYS APDL. i run the model upto ultimate failure, now i want to check the stresses in steel bars...

12 June 2019 7,168 3 View

How to model over reinforced section to check the failure mode?

i model a beam as Over Reinforced Section (ORS), Ast > Ast,lim), using solid65, link8 and solid45 in ANSYS APDL V12, used '"MISO" property to concrete (M20) for stress strain curve, to model...

04 June 2019 9,581 4 View

What is the concept of shear transfer open and close coefficient in ansys apdl and how it affects the load deflection behaviour of concrete & crack?

plz see the MS word file attached below and suggest your valuable answer plz.

22 April 2019 5,650 3 View

How to get rid of short piece of DNA contamination in the gel filtration column?

Dear all, I am looking for some help regarding DNA contamination. Before inject my protein sample and I normally treat them with Benzonase, but these days the protein recovery from gel...

22 March 2018 3,264 4 View

How to define different values of fracture for each mode using the mode independent principle in abaqus ?

Dear All, How to define different values of fracture energy for each mode by using the principle of pure mode independent behavior in abaqus. particularly using cohesive surface approach. Thank you

20 March 2018 9,874 4 View

How to get the antibody for hight molecular weight protein 250KD to work?

I'm working on T type calcium channel. I have knockout the t type calcium channel isoform by CRISPR cas9 method. At the DNA level, I could see the shifted band in the agarose gel in comparison...

05 September 2017 8,809 8 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View