How to create a voxel mesh for a 3d model and import it into COMSOL?

Devorshi Bhattacharjee @Devorshi-Bhattacharjee

23 February 2022 1 5K Report

Hi all, I wanted to know how to create a voxel mesh for a 3d model and import the voxel mesh into COMSOL. Thank you all.

Luigi Candido

You cannot with actual features of COMSOL.

You can try some algorithms in MATLAB and then export your finalized mesh in COMSOL. Try to look here:

https://www.comsol.com/forum/thread/6581/import-mri-ct-and-microct-data

Hope it helps.

Regards

Badges
Science topic

More Devorshi Bhattacharjee's questions See All

Are there any travel grants available in India for independent researchers to attend international conferences?

As a former PhD scholar, currently working as a Junior Research Fellow on a DST-funded project, I am seeking information on travel grants. A few months ago, while I was still pursuing my PhD, I...

03 February 2024 2,050 0 View

What is the normal global DNA methylation level in blood? What is its level in case of breast cancer ?

Trying to find the relationship between epigenetic and cancer more deeply.

30 December 2023 8,363 2 View

CST - ESPIC solver help ?

Hello all , I have a two-plate configuration and there is a dielectric in between them . I launch electrons from plate and it reaches another plates through the dielectric . I kept the dielectric...

16 October 2023 5,702 0 View

How to get the accurate Auto-correlation function of free energy change of binding of the protein-ligand complex ?

Hello, I have performed MM-PBSA calculation of a protein-ligand complex. I utilised approx 750 frames (out of a total of 15000 frames) to compute the free enrgy change of binding. Then, I used a...

04 October 2023 247 2 View

How researchers design primers for a novel virus's genome sequences?

primers are short oligonucleotides specifically designed for sequencing and PCR. But if we don't know where to start sequencing for a novel virus's genome then how the primers can be designed? or...

19 September 2023 4,636 3 View

Why women are more prone to breast cancer men?

Cancer means the uncontrol cell division, but what factors increase the risk of breast cancer in females other than the genetic issue?

18 September 2023 5,790 4 View

Can anyone help me regarding microplastic particle retrival during polymer identification via ATR-FTIR?

How can I pick up the microplastic particle when doing FTIR-ATR? Beacuse I can not directly place my filter paper under ATR.

01 September 2023 2,004 9 View

What is the optimized sonication time in CHIP Qpcr?

I am starting my CHIP qPCR on MCF7 and MDAmb231 cell lines and I am Using the IMPRINT CHIP kit by Sigma. I need to optimize the sonication time for both cell lines, but the buffers are very...

03 August 2023 3,170 0 View

Should a protein- protein interactome be constructed using only upregulated DEGs?

I have a comparative transcriptome dataset, with a number of upregulated and downregulated genes. I want to construct a protein-protein interactome network to understand the node and hub genes and...

23 July 2023 3,286 0 View

How to estimate different organic phosphorus fractions in agricultural soils?

Although there are several research papers describing methods to estimate different organic phosphorus fractions, I did not found any comprehensive method to estimate different organic P...

25 June 2023 6,228 0 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View